Seakeeper 40 Installation Manual (90715-2) 40-234-0043 to Current
5.0 Installation Requirements
5.1 Installation Requirements Introduction
The Installation Requirements section outlines the components and tools needed for the Seakeeper 40 Installation that are not included within the scope of supply.
5.2 Required Supplies for Seakeeper Installation
Required Supplies Needed for Seakeeper Installation
(Not Supplied With the Seakeeper)
| Item | Description | Qty | Installation Manual Reference Section | Other Reference | System |
|---|---|---|---|---|---|
| 1 | Adhesive and cleaning supplies (for bond-in installation) (Total area of adhesive is 1,300 in.2 (8,387 cm2)) | AR | 2.5 Mechanical Installation | Adhesive manufacturer’s instructions and Dwg 90878 | Mechanical |
| 2 | Soundproofing Considerations | AR | 2.2 Selection of Installation Location | Mechanical | |
| 3 | Spreader bar for lifting Seakeeper | 1 | 1.2 Transport and Unpacking | P/N 80029 | Mechanical |
| 4 | Hose clamps for seawater plumbing to 1 in. (25.4 mm) hose barb (2 per hose barb) | 4 | 4.3 Connecting Seawater to Heat Exchanger | Cooling | |
| 5 | 3/4″ to 1″ Hose Adapter | 1 | 4.3 Connecting Seawater to Heat Exchanger | Cooling | |
| 6 | Circuit Breaker, AC, 2-Pole, 20 A | 1 | 3.2 Electrical Equipment Power Connections | Dwg 90710 | Electrical |
| 7 | Circuit Breaker, DC, 1-Pole, 15 A for control power | 1 | 3.2 Electrical Equipment Power Connections | Dwg 90710 | Electrical |
| 8 | Circuit Breaker, DC, 1-Pole, 20 A for seawater pump | 1 | 3.2 Electrical Equipment Power Connections | Dwg 90710 | Electrical |
| 9 | M6 terminal lug for grounding Seakeeper at rear of foundation | 1 | 3.3 Electrical Equipment Ground Connections | Electrical | |
| 10 | Cable, 10 AWG, for grounding Seakeeper at rear brace to vessel ground | AR | 3.3 Electrical Equipment Ground Connections | Dwg 90710 | Electrical |
| 11 | Seawater pump, 24 VDC | 1 | 3.2 Electrical Equipment Power Connections | P/N 30490 available | Electrical |
| 12 | Relay for seawater pump control (Optional) | 1 | 3.2 Electrical Equipment Power Connections | Electrical | |
| 13 | Sili-Thane 803 Sealant (or equivalent) | AR | 2.4.3 Mechanical Installation 2.5.3 Mechanical Installation | Mechanical | |
| 14 | Nickel-based Anti-Seize | AR | 2.4.3 Mechanical Installation 2.5.3 Mechanical Installation | Mechanical |
AR = As Required
Dwg = Drawing
5.3 Tools Required for Installation
List of Common Tools That May Be Required for Installation
| Item | Description | Use |
|---|---|---|
| 1 | Wire cutter | DC Power, AC Power cables |
| 2 | Wire stripper | DC Power, AC Power cables |
| 3 | Phillips head screwdriver | Cover Panels |
| 4 | 13 mm Socket Wrench | Cover Panels |
| 5 | 3 mm hex key | Gimbal sensor mount plate |
| 6 | 2.5 mm hex key | Gimbal angle sensor |
| 7 | ΒΌ in. nut driver/flat tip screwdriver | Hose clamps |
| 8 | Terminal or quick disconnect crimper | Power cables |
| 9 | Utility knife | Scoring cable jackets |
| 10 | 10 mm Socket Wrench | Ground stud & panels |
| 11 | Hoist, Forklift, or Crane | Unpacking and lifting Seakeeper into position |
| 12 | Drill/Drill Press | Bolt hole penetrations |
| 13 | Threaded Insert Installation Kit (Blind Hole Installation only) | Tap and install threaded inserts for M16-2.0. 1-inch length |
| 14 | 1/2 in. Drive Torque Wrench | Foundation fastener torqueing |
| 15 | 24 mm Socket, 1/2 in. drive | Foundation mounting screws |
| 16 | Fish tape | Cable pulls |
| 17 | Hole Saw | Through-hull fittings |