Seakeeper 3 Installation Manual (90378-6); S/N 3-223-3836 to 3-231-4222
5.2 Required Supplies for Seakeeper Installation
Table 1 outlines the customer-supplied components required for the Seakeeper 3 installation:
Table 1: Components and Supplies Required for Seakeeper 3 Installation
| Item | Description | QTY | Installation Manual Reference Section | Other Reference | System |
| 1 | Spreader bar for lifting the Seakeeper | 1 | Transport & Unpacking | P/N 11766 | Mechanical |
| 2 | Seakeeper 3 Fixture Kit | 1 | Bolt-In Installation | P/N 90362 | Mechanical |
| 3 | Threaded insert M16-2 (24 mm) | 4 | Bolt-In Installation | Dwg 90374 | Mechanical |
| 4 | Seakeeper 3 Bolt-In Kit | 1 | Bolt-In Installation | P/N 90375 | Mechanical |
| 5 | Seakeeper 3 Thru-Bolt Kit | 1 | Bolt-In Installation | P/N 90641 | Mechanical |
| 6 | Marine Sealant | AR | Bolt-In Installation | Dwg 90374 | Mechanical |
| 7 | Nickel-based Anti-seize | AR | Bolt-In Installation | Dwg 90374 | Mechanical |
| 8 | Circuit Breaker, 100A (Cable 1) | 1 | Electrical Equipment Power Connections | Dwg 90377 | Electrical |
| 9 | Circuit Breaker, 15 A (Cable 7 & 8) | 2 | Electrical Equipment Power Connections | Dwg 90377 | Electrical |
| 10 | Battery Isolator Switch (Cable 1, 7, & 8) | 1 | Electrical Equipment Power Connections | Dwg 90377 | Electrical |
| 11 | M6 terminal lug for grounding Seakeeper | 1 | Electrical Equipment Ground Connections | Dwg 90377 | Electrical |
| 12 | Cable, 4 AWG, for grounding Seakeeper at rear brace to vessel ground (Cable 6, used with item 11) | 1 | Electrical Equipment Ground Connections | Dwg 90377 ABYC E-11 | Electrical |
| 13 | Seawater pump, 12VDC, 15 A max Optional: DC Seawater Pump Assembly (pre-wired) | 1 | Electrical Equipment Power Connections | Dwg 90377 P/N 30331 | Electrical / Cooling |
| 14 | Seakeeper 5″ Touch Display and Optional Compatible MFD | 1 | Electrical Equipment Power Connections | Dwg 90377 TB-90640 / P/N90600 | Electrical |
| 15 | Through-hull fittings (1 high-speed pick-up / 1 overboard discharge) | 2 | Connecting Seawater to Heat Exchanger | Dwg 90376 | Cooling |
| 16 | Seawater Strainer *included with Seakeeper Seawater Pump(P/N 30331) | 1 | Connecting Seawater to Heat Exchanger | Dwg 90376 | Cooling |
| 17 | Seacock Valve | Connecting Seawater to Heat Exchanger | Dwg 90376 | Cooling | |
| 18 | 3/4 in. (19 mm) ID Seawater Suction Hose AND Discharge Hose | AR | Connecting Seawater to Heat Exchanger | Dwg 90376 | Cooling |
| 19 | Hose clamps for seawater plumbing to ¾ in. (19 mm) hose barb (2 per hose barb) | 4 | Connecting Seawater to Heat Exchanger | Dwg 90376 | Cooling |
AR = As Required
Dwg = Drawing