![\"\"](\"https:\/\/manuals.seakeeper.com\/seakeeper\/wp-content\/uploads\/Cooling-image-1.png\")
\n\n\n\n
- \n
- Connect the seawater pump to the Seakeeper<\/span><\/span> dedicated through-hull fitting. A seacock valve, and a strainer should be installed between the seawater inlet and the pump (See Figure 45).<\/li>\n\n\n\n
- Connect seawater from the installer-supplied pump to the lower \u00be in. (19 mm) hose barb on the heat exchanger. Use the same practices as other below-waterline seawater plumbing. Required flow rate is 4.5 GPM (17 LPM) minimum and 6 GPM (22.7 LPM) maximum.<\/li>\n<\/ol>\n\n\n\n
- \n
- Connect the seawater discharge (upper hose barb) to the overboard drain. It is recommended to install a visible flow meter in the discharge line, though it is not required for permanent installation. Use the same practices as other below-waterline seawater plumbing.<\/li>\n\n\n\n
- In addition to initial operation at the dock, new installations should be checked for seawater flow while the vessel is at speed and when backing down. The flows should be recorded when the seawater pump is running and when it is off.
\n- \n
- If no other method of confirming flow is available, the discharge line may be temporarily diverted to a bucket. Flow is calculated from the time required to fill a known volume (e.g., a 5-gal. bucket).<\/li>\n\n\n\n
- A self-priming seawater pump (customer\/installer supplied) may be required at the installation location to maintain water flow in all underway conditions where cavitation may occur and potentially cause an air lock, restricting seawater flow to the heat exchanger.<\/li>\n<\/ul>\n<\/li>\n\n\n\n
- Inspect raw water plumbing after sea trial for any signs of leakage.<\/li>\n\n\n\n
- The heat exchanger has removable end caps to provide access for cleaning the tube bundle.<\/li>\n<\/ol>\n\n\n\n
\n\n\n\nSeakeeper<\/span> Optional DC Seawater Pump (P\/N 30685)<\/h3>\n\n\n\n
- \n
- Seakeeper<\/span><\/span> offers a self-priming DC Seawater pump as an optional addition, P\/N 30685\u2013 DC Seawater Pump Assembly, shown in Figure 29.<\/li>\n\n\n\n
- The Seakeeper<\/span><\/span> Seawater Pump is a 12 VDC pump.<\/li>\n\n\n\n
- The pump assembly is pre-wired for connection to Seakeeper<\/span><\/span> 7.5 “DC Seawater Pump Out” cable and includes a seawater strainer and various fittings. The pump specifications are as follows:<\/li>\n<\/ol>\n\n\n\n
Note:<\/strong> Use only SeaFlo\u00ae<\/sup>-provided threaded fittings for DC Seawater Pump 30685.<\/p>\n\n\n\n
Volts<\/td> 12 VDC<\/td><\/tr> Rated Flow<\/td> 5.5 GPM (20.8 LPM), maximum<\/td><\/tr> Overcurrent Protection Rating<\/td> 15 A at 12 Volts<\/td><\/tr> Ignition Protection<\/td> ISO 8846 or equivalent<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n \n![\"\"](\"https:\/\/manuals.seakeeper.com\/seakeeper\/wp-content\/uploads\/30685-pump-1.png\")
Figure 29<\/em><\/strong>– Seakeeper<\/span> 7.5 DC Seawater Pump (P\/N 30685)<\/em><\/figcaption><\/figure>\n<\/div>","protected":false},"excerpt":{"rendered":" Connecting Seawater to Heat Exchanger Refer to Figure 28 for typical seawater plumbing arrangement. Seakeeper Optional DC Seawater Pump (P\/N 30685) Note: Use only SeaFlo\u00ae-provided threaded fittings for DC Seawater Pump 30685. Volts 12 VDC Rated Flow 5.5 GPM (20.8 LPM), maximum Overcurrent Protection Rating 15 A at 12 Volts Ignition Protection ISO 8846 or […]<\/p>\n","protected":false},"author":9,"featured_media":0,"parent":21330,"menu_order":0,"comment_status":"closed","ping_status":"closed","template":"","meta":{"_acf_changed":false,"footnotes":""},"manual":[373],"model":[],"document_type":[],"hidden":[],"class_list":["post-21336","page","type-page","status-publish","hentry","manual-seakeeper-7-5-installation-manual"],"acf":[],"_links":{"self":[{"href":"https:\/\/manuals.seakeeper.com\/seakeeper\/wp-json\/wp\/v2\/pages\/21336","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/manuals.seakeeper.com\/seakeeper\/wp-json\/wp\/v2\/pages"}],"about":[{"href":"https:\/\/manuals.seakeeper.com\/seakeeper\/wp-json\/wp\/v2\/types\/page"}],"author":[{"embeddable":true,"href":"https:\/\/manuals.seakeeper.com\/seakeeper\/wp-json\/wp\/v2\/users\/9"}],"replies":[{"embeddable":true,"href":"https:\/\/manuals.seakeeper.com\/seakeeper\/wp-json\/wp\/v2\/comments?post=21336"}],"version-history":[{"count":8,"href":"https:\/\/manuals.seakeeper.com\/seakeeper\/wp-json\/wp\/v2\/pages\/21336\/revisions"}],"predecessor-version":[{"id":22633,"href":"https:\/\/manuals.seakeeper.com\/seakeeper\/wp-json\/wp\/v2\/pages\/21336\/revisions\/22633"}],"up":[{"embeddable":true,"href":"https:\/\/manuals.seakeeper.com\/seakeeper\/wp-json\/wp\/v2\/pages\/21330"}],"wp:attachment":[{"href":"https:\/\/manuals.seakeeper.com\/seakeeper\/wp-json\/wp\/v2\/media?parent=21336"}],"wp:term":[{"taxonomy":"manual","embeddable":true,"href":"https:\/\/manuals.seakeeper.com\/seakeeper\/wp-json\/wp\/v2\/manual?post=21336"},{"taxonomy":"model","embeddable":true,"href":"https:\/\/manuals.seakeeper.com\/seakeeper\/wp-json\/wp\/v2\/model?post=21336"},{"taxonomy":"document_type","embeddable":true,"href":"https:\/\/manuals.seakeeper.com\/seakeeper\/wp-json\/wp\/v2\/document_type?post=21336"},{"taxonomy":"hidden","embeddable":true,"href":"https:\/\/manuals.seakeeper.com\/seakeeper\/wp-json\/wp\/v2\/hidden?post=21336"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}
- The Seakeeper<\/span><\/span> Seawater Pump is a 12 VDC pump.<\/li>\n\n\n\n
- Seakeeper<\/span><\/span> offers a self-priming DC Seawater pump as an optional addition, P\/N 30685\u2013 DC Seawater Pump Assembly, shown in Figure 29.<\/li>\n\n\n\n
- Connect seawater from the installer-supplied pump to the lower \u00be in. (19 mm) hose barb on the heat exchanger. Use the same practices as other below-waterline seawater plumbing. Required flow rate is 4.5 GPM (17 LPM) minimum and 6 GPM (22.7 LPM) maximum.<\/li>\n<\/ol>\n\n\n\n