{"id":20670,"date":"2025-11-12T17:56:37","date_gmt":"2025-11-12T17:56:37","guid":{"rendered":"https:\/\/manuals.seakeeper.com\/seakeeper\/seakeeper-10-installation-manual-90841-1-copy\/electrical-installation\/electrical-equipment-power-connections-2\/"},"modified":"2026-01-06T17:38:15","modified_gmt":"2026-01-06T17:38:15","slug":"electrical-equipment-power-connections-2","status":"publish","type":"page","link":"https:\/\/manuals.seakeeper.com\/seakeeper\/seakeeper-10-installation-manual-90841-2\/electrical-installation\/electrical-equipment-power-connections-2\/","title":{"rendered":"3.2 Electrical Equipment Power Connections"},"content":{"rendered":"\n

230 VAC Power Source Requirements<\/h2>\n\n\n\n
    \n
  1. 230 VAC (nominal), 1 Phase, 50\/60 Hz, 30 A<\/li>\n\n\n\n
  2. For installations of more than one Seakeeper<\/span><\/span>, a separate circuit breaker should be used for each Seakeeper<\/span><\/span> Motor Drive Box.<\/li>\n<\/ol>\n\n\n\n
    \n\n\n\n

    Drive Box AC Power Input Connection Instructions<\/h3>\n\n\n\n
      \n
    1. 230 VAC Input Cable: 3 x 10 AWG (3 x 6 mm2<\/sup> CSA), 10 ft. (3 m) length, Seakeeper<\/span><\/span> supplied pre-installed.
      \n
        \n
      1. Locate 230 VAC Input Cable for AC power input to the Drive Box at the outboard of the Motor Drive Box cable glands.<\/li>\n<\/ol>\n<\/li>\n<\/ol>\n\n\n
        \n
        \"\"
        Figure 19<\/em><\/strong> – Drive Box AC Power Input and Motor Output Glands<\/em><\/figcaption><\/figure>\n<\/div>\n\n
        \n
        \"\"
        Figure 20<\/em><\/strong> – 230 VAC Input Cable Wire <\/em>
        Connections at AC Power Distribution Panel<\/em><\/figcaption><\/figure>\n<\/div>\n\n\n
          \n
        1. Connect 230 VAC Input Cable wires to a 30 A, double-pole Circuit Breaker at an AC power distribution panel according to Figure 20 above.<\/li>\n<\/ol>\n\n\n\n
          \n\n\n\n

          24 VDC Power Source Requirements<\/h2>\n\n\n\n
            \n
          1. Seakeeper<\/span><\/span> Control Power: one 24 VDC, 10 A (Customer supplied), AND<\/strong><\/li>\n\n\n\n
          2. Seawater Pump: one 24 VDC, 10 A*<\/sup> Max (Customer supplied), seawater pump dependent.<\/li>\n\n\n\n
          3. A separate breakers should be used for each Seakeeper<\/span><\/span> in multiple Seakeeper<\/span><\/span> installations.<\/li>\n<\/ol>\n\n\n\n

            * Alternate seawater pump configuration for customer-supplied DC-powered seawater pump, 24 VDC at 20 A maximum.<\/p>\n\n\n\n

            \n\n\n\n

            DC Power Connection Instructions<\/h2>\n\n\n\n
            \n
            \n
            \"\"<\/figure>\n<\/div><\/div>\n\n\n\n
            \n

            <\/p>\n\n\n\n

            Reversing polarity on the DC power input to the Seakeeper<\/span><\/span><\/span> can result in damaging the electronics in the control system.<\/strong><\/p>\n<\/div>\n<\/div>\n\n\n\n

              \n
            1. 24 VDC, 10 A, 2 x 12 AWG (3 x 4.0 mm2<\/sup> CSA) customer supplied.
              \n
                \n
              1. Install Seakeeper<\/span><\/span><\/span><\/span> provided DC Power Input Cable, P\/N 20248 (as shown in Drawing No. 90719<\/strong>).
                \n
                  \n
                1. Route 24 VDC Power Cable to DC Power Distribution Panel.<\/li>\n\n\n\n
                2. Terminate positive (B+, Red ) conductor to +24 VDC. <\/li>\n\n\n\n
                3. Terminate negative (B-, Black) conductor directly to battery negative terminal.<\/li>\n<\/ol>\n<\/li>\n\n\n\n
                4. Before connecting cable to Seakeeper<\/span><\/span><\/span><\/span>, check for proper voltage and polarity with a DC multimeter using Figure 21 below.<\/li>\n\n\n\n
                5. Connect 24 VDC Input Cable to 24 VDC input receptacle on Seakeeper<\/span><\/span><\/span><\/span>.<\/li>\n<\/ol>\n<\/li>\n<\/ol>\n\n\n
                  \n
                  \"\"
                  Figure 21 \u2013 <\/strong>DC Power Input Connector Contact Assignments (front)<\/em><\/figcaption><\/figure>\n<\/div>\n\n\n
                  \n\n\n\n

                  DC Seawater Pump 24 VDC Power Input Connection Instructions<\/h2>\n\n\n\n
                  \n
                  \n
                  \"\"<\/figure>\n<\/div><\/div>\n\n\n\n
                  \n

                  <\/p>\n\n\n\n

                  Connecting the DC Seawater pump in any other manner than recommended by Seakeeper<\/span><\/span><\/span> may cause internal failure.<\/strong><\/p>\n<\/div>\n<\/div>\n\n\n\n

                    \n
                  1. Install Seawater Pump Input Cable (P\/N 20454) to Seakeeper<\/span><\/span> 10 \u201cSW Pump DC In\u201d (as shown in Drawing No. 90719<\/strong>) with overcurrent protection corresponding to seawater pump selected.<\/li>\n\n\n\n
                  2. Connect the 14 AWG positive conductor (Red) through dedicated overcurrent protection device (customer supplied), 10 A (20 A maximum), to dedicated battery isolation switch.<\/li>\n\n\n\n
                  3. Connect the 14 AWG negative conductor (Black) directly to battery negative terminal or DC main negative bus bar.<\/li>\n\n\n\n
                  4. Before connecting Seawater Pump Input Cable to Seakeeper<\/span><\/span>, check for proper voltage and polarity with a DC multimeter using Figure 8 below.<\/li>\n<\/ol>\n\n\n
                    \n
                    \"\"
                    Figure 22<\/strong> – 24 VDC Seawater Pump Power Input<\/em><\/figcaption><\/figure>\n<\/div>\n\n\n
                      \n
                    1. Connect Seawater Pump Input Cable to Seawater Pump 24 VDC In connector on the Seakeeper<\/span><\/span>, DEUTSCH DT04-2P connector.<\/li>\n<\/ol>\n\n\n\n
                      \n\n\n\n

                      DC Seawater Pump 24 VDC Power Output Connection Instructions<\/h2>\n\n\n\n
                        \n
                      1. Connect Seawater Pump Output Cable to the Seakeeper<\/span><\/span> 10 \u201cSW Pump 24VDC Out\u201d for DC power to the seawater pump.
                        \n
                          \n
                        1. Install Y-Branch SW Pump Output & Valve cable (P\/N 20658) to end of “SW Pump 24VDC Out” cable as shown in top image of Figure 24.<\/li>\n\n\n\n
                        2. Seawater Pump Output Cable is a 2 x 14 AWG cable, 16 ft (5m) length with a size 14 female Deutsch plug.<\/li>\n<\/ol>\n<\/li>\n\n\n\n
                        3. Pumps rated at 24 VDC, 10 A maximum, customer-supplied, must be configured with a Deutsch
                          DTP04-2P, 2-pin receptacle to mate with the connector shown in Figure 23.<\/li>\n<\/ol>\n\n\n
                          \n
                          \"\"
                          Figure 23 <\/em><\/strong>– Seawater Pump Deutsch Connector<\/em><\/figcaption><\/figure>\n<\/div>\n\n\n
                            \n
                          1. Seawater Pump Output Cable must be routed and installed in the vessel from the Seakeeper<\/span><\/span> 10 \u201cSW Pump 24VDC Out\u201d Deutsch connector (pins end) to the Y-branch cable Deutsch connector (P\/N 20658)(socket end).<\/li>\n\n\n\n
                          2. Connect Y-branch cable plug end (socket end) to the customer-supplied receptacle end (pins end). The recommended wiring is shown in Figure 24.<\/li>\n\n\n\n
                          3. Connect Y-branch cable DTM-2S connector to DTM-2P connector of inline 1 A fuse cable (P\/N 20794) and the electric valve.<\/li>\n\n\n\n
                          4. Contact Seakeeper<\/span><\/span> if desired to install customer-supplied relay on Seawater Pump Output Cable to power seawater pump and valve.<\/li>\n<\/ol>\n\n\n
                            \n
                            \"\"
                            Figure 24<\/em><\/strong> – 24 VDC SW Pump Schematic<\/em><\/figcaption><\/figure>\n<\/div>","protected":false},"excerpt":{"rendered":"

                            230 VAC Power Source Requirements Drive Box AC Power Input Connection Instructions 24 VDC Power Source Requirements * Alternate seawater pump configuration for customer-supplied DC-powered seawater pump, 24 VDC at 20 A maximum. DC Power Connection Instructions Reversing polarity on the DC power input to the Seakeeper can result in damaging the electronics in the […]<\/p>\n","protected":false},"author":9,"featured_media":0,"parent":20666,"menu_order":0,"comment_status":"closed","ping_status":"closed","template":"","meta":{"_acf_changed":false,"footnotes":""},"manual":[365],"model":[],"document_type":[],"hidden":[],"class_list":["post-20670","page","type-page","status-publish","hentry","manual-seakeeper-10-installation-manual-90841-2"],"acf":[],"_links":{"self":[{"href":"https:\/\/manuals.seakeeper.com\/seakeeper\/wp-json\/wp\/v2\/pages\/20670","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/manuals.seakeeper.com\/seakeeper\/wp-json\/wp\/v2\/pages"}],"about":[{"href":"https:\/\/manuals.seakeeper.com\/seakeeper\/wp-json\/wp\/v2\/types\/page"}],"author":[{"embeddable":true,"href":"https:\/\/manuals.seakeeper.com\/seakeeper\/wp-json\/wp\/v2\/users\/9"}],"replies":[{"embeddable":true,"href":"https:\/\/manuals.seakeeper.com\/seakeeper\/wp-json\/wp\/v2\/comments?post=20670"}],"version-history":[{"count":6,"href":"https:\/\/manuals.seakeeper.com\/seakeeper\/wp-json\/wp\/v2\/pages\/20670\/revisions"}],"predecessor-version":[{"id":21200,"href":"https:\/\/manuals.seakeeper.com\/seakeeper\/wp-json\/wp\/v2\/pages\/20670\/revisions\/21200"}],"up":[{"embeddable":true,"href":"https:\/\/manuals.seakeeper.com\/seakeeper\/wp-json\/wp\/v2\/pages\/20666"}],"wp:attachment":[{"href":"https:\/\/manuals.seakeeper.com\/seakeeper\/wp-json\/wp\/v2\/media?parent=20670"}],"wp:term":[{"taxonomy":"manual","embeddable":true,"href":"https:\/\/manuals.seakeeper.com\/seakeeper\/wp-json\/wp\/v2\/manual?post=20670"},{"taxonomy":"model","embeddable":true,"href":"https:\/\/manuals.seakeeper.com\/seakeeper\/wp-json\/wp\/v2\/model?post=20670"},{"taxonomy":"document_type","embeddable":true,"href":"https:\/\/manuals.seakeeper.com\/seakeeper\/wp-json\/wp\/v2\/document_type?post=20670"},{"taxonomy":"hidden","embeddable":true,"href":"https:\/\/manuals.seakeeper.com\/seakeeper\/wp-json\/wp\/v2\/hidden?post=20670"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}