{"id":17498,"date":"2025-01-08T19:06:05","date_gmt":"2025-01-08T19:06:05","guid":{"rendered":"https:\/\/manuals.seakeeper.com\/seakeeper\/seakeeper-9-installation-manual-90222-11-s-n-9-233-4900-to-current-copy\/start-up\/installation-checklist\/"},"modified":"2025-01-08T19:06:05","modified_gmt":"2025-01-08T19:06:05","slug":"installation-checklist","status":"publish","type":"page","link":"https:\/\/manuals.seakeeper.com\/seakeeper\/seakeeper-10-installation-manual\/start-up\/installation-checklist\/","title":{"rendered":"6.2 Installation Checklist"},"content":{"rendered":"\n

Please Complete Checklist and E-mail to <\/strong>
customerservice@seakeeper.com<\/a> or telefax to +1.410.326.1199<\/strong><\/p>\n\n\n\n

6.2.1 Mechanical Checklist
(Reference Installation Manual Section: Mechanical Installation)<\/h2>\n\n\n\n
\n
\n

_____ Seakeeper<\/span><\/span><\/span> foundation installed in hull<\/p>\n\n\n\n

_____ Foundation bolts torqued to specification<\/p>\n<\/div>\n<\/div>\n\n\n\n

\n\n\n\n

6.2.2 Electrical Checklist
(Reference Seakeeper<\/span> Drawing No. 90257 \u2013 Seakeeper<\/span> 10 Cable Block Diagram & Installation Manual Section: Electrical Installation)<\/h2>\n\n\n\n

Mount Components<\/strong><\/p>\n\n\n\n

_____ Optional 5″ Display (near helm or in an accessible location)<\/p>\n\n\n\n

\n\n\n\n

Connect Customer Supplied Cables<\/span><\/strong><\/p>\n\n\n\n

Seakeeper<\/span> Ground Cable <\/strong>(Customer supplied)<\/p>\n\n\n\n

_____ Install lugs on both ends of customer-supplied 10 AWG (6 mm2<\/sup>) ground cable<\/p>\n\n\n\n

_____ Connect one end of ground cable to nearest vessel ground and other end to Seakeeper<\/span> 10 rear
brace<\/p>\n\n\n\n

Connect Seakeeper<\/span> Supplied Cables<\/span><\/strong><\/p>\n\n\n\n

Control Power Cable<\/strong><\/p>\n\n\n\n

_____ Connect control power cable from Seakeeper<\/span> to 24 VDC power at customer-supplied connection
box or directly to circuit breaker<\/p>\n\n\n\n

_____ Plug connector of control power cable into mating connector on Seakeeper<\/span> wire harness<\/p>\n\n\n\n

AC Input Cable<\/strong><\/p>\n\n\n\n

_____ Connect AC input cable from Drive Box to 230 VAC single phase at customer-supplied connection
box or directly to circuit breaker<\/p>\n\n\n\n

DC Seawater Pump Power Cable<\/strong><\/p>\n\n\n\n

_____ Connect DC seawater pump power input cable from Seakeeper<\/span> to 24 VDC \/10 A power at customer-
supplied connection box or directly to circuit breaker<\/p>\n\n\n\n

_____ Plug connector of DC seawater pump power cable into mating connector on Seakeeper<\/span> wire
harness at DC SW Pump In<\/em><\/p>\n\n\n\n

DC Seawater Pump Output Cable<\/strong><\/p>\n\n\n\n

_____ Connect seawater pump output cable from DC SW Pump Out<\/em> to 24 VDC seawater pump<\/p>\n\n\n\n

MFD Ethernet Adapter Cable<\/strong><\/p>\n\n\n\n

_____ Connect male end of ethernet adapter cable to Ethernet<\/em> connection on ConnectBox<\/p>\n\n\n\n

_____ Route ethernet adapter cable to selected MFD compatibility cable towards helm<\/p>\n\n\n\n

_____ Connect female end of ethernet adapter cable to MFD compatibility cable<\/p>\n\n\n\n

_____ Connect MFD compatibility cable to MFD Display<\/p>\n\n\n\n

OPTIONAL Seakeeper<\/span> 5″ Display CAN Cable<\/strong><\/p>\n\n\n\n

_____ Connect female end of CAN communication cable to tee-adapter at ConnectBox
(at tee-adapter terminal resistor)<\/p>\n\n\n\n

_____ Route CAN communication cable to Seakeeper<\/span> 5″ display<\/p>\n\n\n\n

_____ Connect male end of CAN communication cable to tee-adapter with terminal resistor at 5″ display<\/p>\n\n\n\n

\n\n\n\n

6.2.3 Cooling Checklist
(Reference Installation Manual Section: Cooling Installation)<\/h2>\n\n\n\n

_____ Verify coolant level in coolant reservoir<\/p>\n\n\n\n

_____ Connect seawater hoses \/ open sea cocks to heat exchanger and test seawater pump<\/p>\n\n\n\n

_____ Verify 4.5 GPM (17 LPM) minimum and 6 GPM (22.7 LPM) maximum seawater flow through heat
heat exchanger under all operating conditions of the boat<\/p>\n\n\n\n

\n\n\n\n

6.2.4 Start-Up Checklist
(Reference Installation Manual Section: Start Up & Operation Manual Section: System Operation)<\/h2>\n\n\n\n

_____ Remove lifting eyebolts and install cover panels<\/p>\n\n\n\n

_____ Turn on 24 VDC circuit breakers<\/p>\n\n\n\n

_____ Turn on 230 VAC circuit breaker<\/p>\n\n\n\n

_____ Verify display works and no ALARMS are present<\/p>\n\n\n\n

_____ If display does not work, turn off both circuit breakers immediately<\/p>\n\n\n\n

_____ Follow instructions in Installation Manual Section: Start-Up Instructions to turn on the Seakeeper<\/span><\/p>\n\n\n\n

_____ Verify seawater pump turns on while the Seakeeper<\/span> is turned ON. The Seawater Pump operates
intermittently when cooling is needed.<\/p>\n\n\n\n

_____ Verify no ALARMS are present<\/p>\n\n\n\n

_____ Turn off the Seakeeper<\/span><\/p>\n\n\n\n

_____ AC & DC power and seawater pump breakers may be turned off after the Seakeeper<\/span> is turned off.<\/p>\n\n\n\n

_____ Seakeeper<\/span> 10 takes 4+ hours to coast down to 0 RPM from full speed.<\/p>\n","protected":false},"excerpt":{"rendered":"

Please Complete Checklist and E-mail to customerservice@seakeeper.com or telefax to +1.410.326.1199 6.2.1 Mechanical Checklist(Reference Installation Manual Section: Mechanical Installation) _____ Seakeeper foundation installed in hull _____ Foundation bolts torqued to specification 6.2.2 Electrical Checklist(Reference Seakeeper Drawing No. 90257 \u2013 Seakeeper 10 Cable Block Diagram & Installation Manual Section: Electrical Installation) Mount Components _____ Optional 5″ […]<\/p>\n","protected":false},"author":9,"featured_media":0,"parent":17494,"menu_order":0,"comment_status":"closed","ping_status":"closed","template":"","meta":{"_acf_changed":false,"footnotes":""},"manual":[322],"model":[],"document_type":[],"hidden":[],"class_list":["post-17498","page","type-page","status-publish","hentry","manual-seakeeper-10-installation-manual"],"acf":[],"_links":{"self":[{"href":"https:\/\/manuals.seakeeper.com\/seakeeper\/wp-json\/wp\/v2\/pages\/17498","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/manuals.seakeeper.com\/seakeeper\/wp-json\/wp\/v2\/pages"}],"about":[{"href":"https:\/\/manuals.seakeeper.com\/seakeeper\/wp-json\/wp\/v2\/types\/page"}],"author":[{"embeddable":true,"href":"https:\/\/manuals.seakeeper.com\/seakeeper\/wp-json\/wp\/v2\/users\/9"}],"replies":[{"embeddable":true,"href":"https:\/\/manuals.seakeeper.com\/seakeeper\/wp-json\/wp\/v2\/comments?post=17498"}],"version-history":[{"count":8,"href":"https:\/\/manuals.seakeeper.com\/seakeeper\/wp-json\/wp\/v2\/pages\/17498\/revisions"}],"predecessor-version":[{"id":19800,"href":"https:\/\/manuals.seakeeper.com\/seakeeper\/wp-json\/wp\/v2\/pages\/17498\/revisions\/19800"}],"up":[{"embeddable":true,"href":"https:\/\/manuals.seakeeper.com\/seakeeper\/wp-json\/wp\/v2\/pages\/17494"}],"wp:attachment":[{"href":"https:\/\/manuals.seakeeper.com\/seakeeper\/wp-json\/wp\/v2\/media?parent=17498"}],"wp:term":[{"taxonomy":"manual","embeddable":true,"href":"https:\/\/manuals.seakeeper.com\/seakeeper\/wp-json\/wp\/v2\/manual?post=17498"},{"taxonomy":"model","embeddable":true,"href":"https:\/\/manuals.seakeeper.com\/seakeeper\/wp-json\/wp\/v2\/model?post=17498"},{"taxonomy":"document_type","embeddable":true,"href":"https:\/\/manuals.seakeeper.com\/seakeeper\/wp-json\/wp\/v2\/document_type?post=17498"},{"taxonomy":"hidden","embeddable":true,"href":"https:\/\/manuals.seakeeper.com\/seakeeper\/wp-json\/wp\/v2\/hidden?post=17498"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}