{"id":15834,"date":"2023-06-15T11:31:00","date_gmt":"2023-06-15T11:31:00","guid":{"rendered":"https:\/\/manuals.seakeeper.com\/seakeeper\/seakeeper-5-6-installation-manual-90402-4-copy\/installation-checklist-and-supplies\/installation-checklist\/"},"modified":"2025-12-03T13:40:54","modified_gmt":"2025-12-03T13:40:54","slug":"installation-checklist","status":"publish","type":"page","link":"https:\/\/manuals.seakeeper.com\/seakeeper\/seakeeper-5-6-installation-manual-90402-5\/installation-checklist-and-supplies\/installation-checklist\/","title":{"rendered":"6.2 Installation Checklist"},"content":{"rendered":"\n

Please Complete Checklist and E-mail to support@seakeeper.com<\/a>. or emeasupoport@seakeeper.com<\/a>.<\/strong><\/p>\n\n\n\n

6.1.1 Mechanical Checklist
(Reference Installation Manual Section: Mechanical Installation)<\/h2>\n\n\n\n
    \n
  • Seakeeper<\/span><\/span> foundation installed in hull<\/li>\n\n\n\n
  • Foundation bolts torqued to specification<\/li>\n<\/ul>\n\n\n\n\n\n

    6.1.2 Electrical Checklist
    (Reference Seakeeper<\/span> Drawing No. 90396 \u2013 Seakeeper<\/span> 5\/6 Cable Block Diagram & Installation Manual Section: Electrical Installation)<\/h2>\n\n\n\n

    Mount Components<\/strong><\/p>\n\n\n\n

      \n
    • Display (near helm)<\/li>\n<\/ul>\n\n\n\n

      Connect Customer Supplied Cables<\/strong><\/p>\n\n\n\n

        \n
      • Cable 3 (Customer Supplied)\n
          \n
        • Install lugs on both ends of customer-supplied 10 AWG ground cable<\/li>\n\n\n\n
        • Connect one end of Cable 3 to nearest vessel ground and other end to Seakeeper<\/span><\/span><\/span><\/span> rear brace<\/li>\n<\/ul>\n<\/li>\n<\/ul>\n\n\n\n

          Connect Seakeeper<\/span> Supplied Cables<\/strong><\/p>\n\n\n\n

            \n
          • Cable 1 (Seakeeper<\/span><\/span> Supplied)\n
              \n
            • Connect other end of Cable 1 to 12 VDC power at customer-supplied connection box or directly to circuit breaker<\/li>\n\n\n\n
            • Plug connector of Cable 1 into mating connector on Seakeeper<\/span><\/span><\/span><\/span> wire harness<\/li>\n<\/ul>\n<\/li>\n\n\n\n
            • Cable 9 (Seakeeper<\/span><\/span> Supplied)\n
                \n
              • Connect Cable 9 from SW PUMP VDC IN<\/em> directly to circuit breaker<\/li>\n<\/ul>\n<\/li>\n\n\n\n
              • Cable 5 (Seakeeper<\/span><\/span> Supplied)\n
                  \n
                • Connect Cable 5 from SW PUMP VDC OUT<\/em> to customer-supplied 12 VDC seawater pump<\/li>\n<\/ul>\n<\/li>\n\n\n\n
                • Cable 4 (Seakeeper<\/span><\/span> Supplied)\n
                    \n
                  • Connect female end of CAN communications Cable 3 to mating connector on Seakeeper<\/span><\/span><\/span><\/span> wire harness<\/li>\n\n\n\n
                  • Route CAN communications Cable 3 from Seakeeper<\/span><\/span><\/span><\/span> to helm (male end goes to helm)<\/li>\n\n\n\n
                  • Connect male end of CAN communications Cable 4 at helm to CAN Tee Adapter<\/li>\n\n\n\n
                  • Connect Display and Seakeeper<\/span><\/span><\/span><\/span>-supplied Cable 4 to CAN Tee Adapter with CAN Terminator<\/li>\n<\/ul>\n<\/li>\n<\/ul>\n\n\n\n\n\n

                    6.1.3 Cooling Checklist
                    (Reference Installation Manual Section: Cooling Installation)<\/h2>\n\n\n\n
                      \n
                    • Verify coolant level just below filler neck in heat exchanger coolant reservoir.<\/li>\n\n\n\n
                    • Connect seawater hoses \/ open sea cocks to heat exchanger and test seawater pump.<\/li>\n\n\n\n
                    • Verify 2.5 GPM (9.5 LPM) minimum and 8 GPM (30 LPM) maximum seawater flow through heat exchanger under all operating conditions of the boat.<\/li>\n<\/ul>\n\n\n\n\n\n

                      6.1.4 Start Up Checklist
                      (Reference Installation Manual Section: Start Up & Operation Manual Section: System Operation)<\/h2>\n\n\n\n
                        \n
                      • Remove lifting bolts and install cover panels<\/li>\n\n\n\n
                      • Turn on 12 VDC circuit breakers (one for power and one for 12 VDC SW Pump)<\/li>\n\n\n\n
                      • Turn on 110-230 VAC circuit breaker<\/li>\n\n\n\n
                      • Verify display works and no ALARMS are present<\/li>\n\n\n\n
                      • Follow instructions in Installation Manual Section: Start Up Instructions to turn on the Seakeeper<\/span><\/span><\/li>\n\n\n\n
                      • Verify seawater pump eventually turns on when the Seakeeper<\/span><\/span> is ON<\/li>\n\n\n\n
                      • Verify that no ALARMS are present<\/li>\n\n\n\n
                      • Follow instructions in Installation Manual Section: Start Up Instructions to turn off the Seakeeper<\/span><\/span><\/li>\n\n\n\n
                      • AC & DC power and seawater pump may be turned off after the Seakeeper<\/span><\/span> is turned off by placing the Seakeeper<\/span><\/span> in LOCK mode and turning the Seakeeper<\/span><\/span> off<\/li>\n\n\n\n
                      • Seakeeper<\/span><\/span> takes 4 or more hours to coast down to 0 RPM from full speed<\/li>\n<\/ul>\n","protected":false},"excerpt":{"rendered":"

                        Please Complete Checklist and E-mail to support@seakeeper.com. or emeasupoport@seakeeper.com. 6.1.1 Mechanical Checklist(Reference Installation Manual Section: Mechanical Installation) 6.1.2 Electrical Checklist(Reference Seakeeper Drawing No. 90396 \u2013 Seakeeper 5\/6 Cable Block Diagram & Installation Manual Section: Electrical Installation) Mount Components Connect Customer Supplied Cables Connect Seakeeper Supplied Cables 6.1.3 Cooling Checklist(Reference Installation Manual Section: Cooling Installation) 6.1.4 […]<\/p>\n","protected":false},"author":9,"featured_media":0,"parent":15832,"menu_order":0,"comment_status":"closed","ping_status":"closed","template":"","meta":{"_acf_changed":false,"footnotes":""},"manual":[309],"model":[],"document_type":[],"hidden":[],"class_list":["post-15834","page","type-page","status-publish","hentry","manual-seakeeper-5-6-installation-manual-90402-5"],"acf":[],"_links":{"self":[{"href":"https:\/\/manuals.seakeeper.com\/seakeeper\/wp-json\/wp\/v2\/pages\/15834","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/manuals.seakeeper.com\/seakeeper\/wp-json\/wp\/v2\/pages"}],"about":[{"href":"https:\/\/manuals.seakeeper.com\/seakeeper\/wp-json\/wp\/v2\/types\/page"}],"author":[{"embeddable":true,"href":"https:\/\/manuals.seakeeper.com\/seakeeper\/wp-json\/wp\/v2\/users\/9"}],"replies":[{"embeddable":true,"href":"https:\/\/manuals.seakeeper.com\/seakeeper\/wp-json\/wp\/v2\/comments?post=15834"}],"version-history":[{"count":3,"href":"https:\/\/manuals.seakeeper.com\/seakeeper\/wp-json\/wp\/v2\/pages\/15834\/revisions"}],"predecessor-version":[{"id":21142,"href":"https:\/\/manuals.seakeeper.com\/seakeeper\/wp-json\/wp\/v2\/pages\/15834\/revisions\/21142"}],"up":[{"embeddable":true,"href":"https:\/\/manuals.seakeeper.com\/seakeeper\/wp-json\/wp\/v2\/pages\/15832"}],"wp:attachment":[{"href":"https:\/\/manuals.seakeeper.com\/seakeeper\/wp-json\/wp\/v2\/media?parent=15834"}],"wp:term":[{"taxonomy":"manual","embeddable":true,"href":"https:\/\/manuals.seakeeper.com\/seakeeper\/wp-json\/wp\/v2\/manual?post=15834"},{"taxonomy":"model","embeddable":true,"href":"https:\/\/manuals.seakeeper.com\/seakeeper\/wp-json\/wp\/v2\/model?post=15834"},{"taxonomy":"document_type","embeddable":true,"href":"https:\/\/manuals.seakeeper.com\/seakeeper\/wp-json\/wp\/v2\/document_type?post=15834"},{"taxonomy":"hidden","embeddable":true,"href":"https:\/\/manuals.seakeeper.com\/seakeeper\/wp-json\/wp\/v2\/hidden?post=15834"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}