{"id":15331,"date":"2023-05-22T10:39:49","date_gmt":"2023-05-22T10:39:49","guid":{"rendered":"https:\/\/manuals.seakeeper.com\/seakeeper\/seakeeper-9-installation-manual-90222-10-copy\/mechanical-installation\/saddle-installation\/check-and-preparation-of-hull-structure\/"},"modified":"2023-09-25T12:46:19","modified_gmt":"2023-09-25T12:46:19","slug":"check-and-preparation-of-hull-structure","status":"publish","type":"page","link":"https:\/\/manuals.seakeeper.com\/seakeeper\/seakeeper-9-installation-manual\/mechanical-installation\/saddle-installation\/check-and-preparation-of-hull-structure\/","title":{"rendered":"2.5.2 Preparation of Hull Structure"},"content":{"rendered":"\n

Refer to Seakeeper<\/span> Drawing No. 90226 \u2013 Seakeeper<\/span> 9 Bond-In Installation Details. Important dimensional and load information is given in this drawing that will impact the design details of the structure that will receive the Seakeeper<\/span> as well as selection of the adhesive to bond the Seakeeper<\/span> into the hull.<\/p>\n\n\n\n

The foundation \u201csaddles\u201d of the Seakeeper<\/span> are designed to be bonded directly to the composite hull structure of the vessel to effectively distribute Seakeeper<\/span> loads. A complete bond is required between the inside surface of the saddles and the hull structure.<\/mark> Seakeeper<\/span> recommends having a minimum of 2.5 L \/ 0.66 gal of adhesive, on hand for installation. Number of cartridges required is determined by dividing total volume by cartridge volume. There is some adhesive waste as a part of the process so a good rule of thumb is to purchase 50% more adhesive than estimated volume to bond. Depending on conditions and adhesive used, two workers may be required to apply the adhesive at the same time to finish the installation before the adhesive starts to cure. To aid in determining the quantity of adhesive required, the interior surface area (bonding surfaces) of each<\/strong> saddle is 106 in.2<\/sup> (684 cm2<\/sup>) for a total bonded surface area for all four saddles of 424 in.2<\/sup> (2,736 cm2<\/sup>).<\/p>\n\n\n\n

The hull structure supporting the Seakeeper<\/span> should be installed so the Seakeeper<\/span> is parallel to the waterline in the transverse direction and within 2 degrees longitudinally. The four areas on top of the beams that the saddles will bond to need to be co-planar within .13 in. (3 mm) for consistent adhesive bond gap. In addition, the four areas on top of the saddles on which the feet of the Seakeeper<\/span> foundation will rest need to be co-planar within .06 in. (1.5 mm) to minimize potential distortion of Seakeeper<\/span> support frame when installed.<\/span><\/p>\n\n\n\n

Note that any paint or gel-coat present in bond area should be removed so that adhesive will bond directly to laminate fibers and resin.<\/mark><\/p>\n\n\n\n

Seakeeper<\/span> provides an installation fixture template, P\/N 90253, that locates the saddles at the proper spacing both in the forward-aft direction and the port-starboard direction. See Figures 11 & 12 below, and Figure 13 in the following section. Once assembled with the provided saddle fittings, the fixture can be used to check clearances and alignment of the hull structure. The fixture will allow the builder \/ installer to lay-up and adjust the foundation dimensions to create a low-clearance fit between the Seakeeper<\/span> foundation saddles and the hull structure. Shear strength of the adhesive will be maximized if the cured thickness between the vessel structure and the Seakeeper<\/span> saddles is at the thinner end of the adhesive manufacturer\u2019s recommended range. Therefore, the fixture should be used to confirm that the overall dimensions of the foundations are square and level and that the adhesive gap is within Seakeeper<\/span>\u2019s recommended range of .04 in. to .13 in. (1 to 3 mm).<\/p>\n\n\n\n

Note: Do NOT use the installation fixture to establish Seakeeper<\/span> envelope dimensions. Refer to Drawing No. 90226 \u2013 Seakeeper<\/span> 9 Bond-In Installation Details<\/strong>, for envelope dimensions. A 3-D model of the Seakeeper<\/span> is available on the Seakeeper<\/span> Technical Library (<\/strong>http:\/\/www.seakeeper.com\/technical-library\/<\/a>) to aid in designing the Seakeeper<\/span> foundation and the space around the Seakeeper<\/span>.<\/strong><\/p>\n\n\n\n

NOTE: MAKE SURE NO OBSTRUCTIONS FROM THE HULL STRUCTURE CAN BE SEEN WITHIN THE INSIDE OF THE INSTALLATION TEMPLATE KIT (INSIDE THE MARKED RED LINES). SEE DRAWING NO. 90226 \u2013 SEAKEEPER 9 BOND-IN INSTALLATION DETAILS.<\/mark><\/p>\n\n\n

\n
\"\"
Figure 11 \u2013 <\/strong>Exploded View of Saddle Installation Fixture<\/em><\/figcaption><\/figure>\n<\/div>\n\n\n
<\/div>\n\n\n
\n
\"\"
Figure 12 \u2013 <\/strong>Saddle Installation Fixture on Notional Hull Structure<\/em><\/figcaption><\/figure>\n<\/div>","protected":false},"excerpt":{"rendered":"

Refer to Seakeeper Drawing No. 90226 \u2013 Seakeeper 9 Bond-In Installation Details. Important dimensional and load information is given in this drawing that will impact the design details of the structure that will receive the Seakeeper as well as selection of the adhesive to bond the Seakeeper into the hull. The foundation \u201csaddles\u201d of the […]<\/p>\n","protected":false},"author":9,"featured_media":0,"parent":15327,"menu_order":0,"comment_status":"closed","ping_status":"closed","template":"","meta":{"_acf_changed":false,"footnotes":""},"manual":[307],"model":[],"document_type":[],"hidden":[],"class_list":["post-15331","page","type-page","status-publish","hentry","manual-seakeeper-9-installation-manual"],"acf":[],"_links":{"self":[{"href":"https:\/\/manuals.seakeeper.com\/seakeeper\/wp-json\/wp\/v2\/pages\/15331","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/manuals.seakeeper.com\/seakeeper\/wp-json\/wp\/v2\/pages"}],"about":[{"href":"https:\/\/manuals.seakeeper.com\/seakeeper\/wp-json\/wp\/v2\/types\/page"}],"author":[{"embeddable":true,"href":"https:\/\/manuals.seakeeper.com\/seakeeper\/wp-json\/wp\/v2\/users\/9"}],"replies":[{"embeddable":true,"href":"https:\/\/manuals.seakeeper.com\/seakeeper\/wp-json\/wp\/v2\/comments?post=15331"}],"version-history":[{"count":1,"href":"https:\/\/manuals.seakeeper.com\/seakeeper\/wp-json\/wp\/v2\/pages\/15331\/revisions"}],"predecessor-version":[{"id":15430,"href":"https:\/\/manuals.seakeeper.com\/seakeeper\/wp-json\/wp\/v2\/pages\/15331\/revisions\/15430"}],"up":[{"embeddable":true,"href":"https:\/\/manuals.seakeeper.com\/seakeeper\/wp-json\/wp\/v2\/pages\/15327"}],"wp:attachment":[{"href":"https:\/\/manuals.seakeeper.com\/seakeeper\/wp-json\/wp\/v2\/media?parent=15331"}],"wp:term":[{"taxonomy":"manual","embeddable":true,"href":"https:\/\/manuals.seakeeper.com\/seakeeper\/wp-json\/wp\/v2\/manual?post=15331"},{"taxonomy":"model","embeddable":true,"href":"https:\/\/manuals.seakeeper.com\/seakeeper\/wp-json\/wp\/v2\/model?post=15331"},{"taxonomy":"document_type","embeddable":true,"href":"https:\/\/manuals.seakeeper.com\/seakeeper\/wp-json\/wp\/v2\/document_type?post=15331"},{"taxonomy":"hidden","embeddable":true,"href":"https:\/\/manuals.seakeeper.com\/seakeeper\/wp-json\/wp\/v2\/hidden?post=15331"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}