{"id":12738,"date":"2023-02-28T16:17:42","date_gmt":"2023-02-28T16:17:42","guid":{"rendered":"https:\/\/manuals.seakeeper.com\/seakeeper\/seakeeper-26-20hd-installation-manual-90265-7-copy\/mechanical-installation\/saddle-installation\/check-and-preparation-of-hull-structure\/"},"modified":"2023-03-01T14:09:22","modified_gmt":"2023-03-01T14:09:22","slug":"check-and-preparation-of-hull-structure","status":"publish","type":"page","link":"https:\/\/manuals.seakeeper.com\/seakeeper\/seakeeper-26-installation-manual-90265-8\/mechanical-installation\/saddle-installation\/check-and-preparation-of-hull-structure\/","title":{"rendered":"2.5.2 Preparation of Vessel Structure"},"content":{"rendered":"\n

Refer to Seakeeper<\/span> Drawing No. 90272 \u2013 Seakeeper<\/span> 26 Bond-In Installation Details. Important dimensional and load information is given in this drawing that will impact the design details of the structure that will receive the Seakeeper<\/span> as well as selection of the adhesive to bond the Seakeeper<\/span> into the hull.<\/p>\n\n\n\n

The foundation \u201csaddles\u201d of the Seakeeper<\/span> are designed to be bonded directly to the composite hull structure of the vessel to effectively distribute Seakeeper<\/span> loads. A complete bond is required between the inside surface of the saddles and the hull structure.<\/mark> Seakeeper<\/span> recommends having a minimum<\/strong> of 2.4 L \/ 0.6<\/strong> gal of adhesive on hand for installation. Some adhesives require etching primer for aluminum surfaces (Plexus MA590 requires PC120 primer). Both manual and pneumatic application guns are available from adhesive manufacturers. Two workers should apply the adhesive at the same time to finish the installation before the adhesive starts to cure. To aid in determining the quantity of adhesive required, the interior surface area (bonding surfaces) of each <\/strong>saddle is 287 in.2<\/sup> (1,852 cm2<\/sup>) for a total bonded surface area for all four saddles of 1,148 in.2<\/sup> (7,406 cm2<\/sup>).<\/p>\n\n\n\n

The hull structure supporting the Seakeeper<\/span> should be arranged so the Seakeeper<\/span> is parallel to the water plane in the port-starboard and forward-aft directions. In addition, the four areas on top of the beams that the saddles will bond to need to be co-planar within 1\/8 in. (3 mm) to minimize potential distortion of Seakeeper<\/span> support frame when installed. The four areas on top of the saddles on which the feet of the Seakeeper<\/span> foundation rest must be coplanar within 0.6 in. (1.5 mm) to minimize potential distortion of Seakeeper<\/span> support frame when installed.<\/mark><\/p>\n\n\n\n

Note that any paint or gel-coat present in bond area should be removed so that adhesive will bond directly to laminate fibers and resin.<\/mark> Fiberglass and aluminum surfaces should be sanded in cross-hatch pattern with 80-grit sandpaper and thoroughly cleaned prior to adhesive application.<\/p>\n\n\n\n

Seakeeper<\/span> provides an installation fixture template (P\/N 90088), that locates the saddles at the proper spacing both in the port-starboard and the forward-aft direction direction. See Figures 6, 7 & 8 below. Once assembled with the provided saddle fittings, the fixture can be used to check clearances and alignment of the hull structure. The fixture will allow the builder \/ installer to lay-up and adjust the foundation dimensions to create a low-clearance fit between the Seakeeper<\/span> foundation saddles and the hull structure. Shear strength of the adhesive will be maximized if the cured thickness between the vessel structure and the Seakeeper<\/span> saddles is at the thinner end of the adhesive manufacturer\u2019s recommended range. Therefore, the fixture should be used to confirm that the overall dimensions of the foundations are square and level and that the adhesive gap is within Seakeeper<\/span>\u2019s recommended range of .04 in. to .13 in. (1 to 3 mm).<\/p>\n\n\n\n

Note: Do NOT use the installation fixture to establish Seakeeper<\/span> envelope dimensions. Refer to Drawing No. 90272 \u2013 Seakeeper<\/span> 26 Bond-In Installation Details<\/strong>, for envelope dimensions. A 3-D model of the Seakeeper<\/span> is available on the Seakeeper<\/span> website (www.seakeeper.com<\/a>) to aid in designing the Seakeeper<\/span> foundation and the space around the Seakeeper<\/span>.<\/strong><\/p>\n\n\n

\n
\"\"
Figure 6 \u2013 <\/strong>Exploded View of Saddle Installation Fixture<\/em><\/figcaption><\/figure>\n<\/div>\n\n\n
<\/div>\n\n\n
\n
\"\"
Figure 7 \u2013 <\/strong>Notice for Checking Square of Assembly<\/em><\/figcaption><\/figure>\n<\/div>\n\n\n
<\/div>\n\n\n
\n
\"\"
Figure 8 \u2013<\/strong> Saddle Installation Fixture on Notional Hull Structure<\/em><\/figcaption><\/figure>\n<\/div>","protected":false},"excerpt":{"rendered":"

Refer to Seakeeper Drawing No. 90272 \u2013 Seakeeper 26 Bond-In Installation Details. Important dimensional and load information is given in this drawing that will impact the design details of the structure that will receive the Seakeeper as well as selection of the adhesive to bond the Seakeeper into the hull. The foundation \u201csaddles\u201d of the […]<\/p>\n","protected":false},"author":9,"featured_media":0,"parent":12734,"menu_order":0,"comment_status":"closed","ping_status":"closed","template":"","meta":{"_acf_changed":false,"footnotes":""},"manual":[277],"model":[],"document_type":[],"hidden":[],"class_list":["post-12738","page","type-page","status-publish","hentry","manual-seakeeper-26-installation-manual-90265-8"],"acf":[],"_links":{"self":[{"href":"https:\/\/manuals.seakeeper.com\/seakeeper\/wp-json\/wp\/v2\/pages\/12738","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/manuals.seakeeper.com\/seakeeper\/wp-json\/wp\/v2\/pages"}],"about":[{"href":"https:\/\/manuals.seakeeper.com\/seakeeper\/wp-json\/wp\/v2\/types\/page"}],"author":[{"embeddable":true,"href":"https:\/\/manuals.seakeeper.com\/seakeeper\/wp-json\/wp\/v2\/users\/9"}],"replies":[{"embeddable":true,"href":"https:\/\/manuals.seakeeper.com\/seakeeper\/wp-json\/wp\/v2\/comments?post=12738"}],"version-history":[{"count":5,"href":"https:\/\/manuals.seakeeper.com\/seakeeper\/wp-json\/wp\/v2\/pages\/12738\/revisions"}],"predecessor-version":[{"id":12911,"href":"https:\/\/manuals.seakeeper.com\/seakeeper\/wp-json\/wp\/v2\/pages\/12738\/revisions\/12911"}],"up":[{"embeddable":true,"href":"https:\/\/manuals.seakeeper.com\/seakeeper\/wp-json\/wp\/v2\/pages\/12734"}],"wp:attachment":[{"href":"https:\/\/manuals.seakeeper.com\/seakeeper\/wp-json\/wp\/v2\/media?parent=12738"}],"wp:term":[{"taxonomy":"manual","embeddable":true,"href":"https:\/\/manuals.seakeeper.com\/seakeeper\/wp-json\/wp\/v2\/manual?post=12738"},{"taxonomy":"model","embeddable":true,"href":"https:\/\/manuals.seakeeper.com\/seakeeper\/wp-json\/wp\/v2\/model?post=12738"},{"taxonomy":"document_type","embeddable":true,"href":"https:\/\/manuals.seakeeper.com\/seakeeper\/wp-json\/wp\/v2\/document_type?post=12738"},{"taxonomy":"hidden","embeddable":true,"href":"https:\/\/manuals.seakeeper.com\/seakeeper\/wp-json\/wp\/v2\/hidden?post=12738"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}