{"id":12601,"date":"2023-02-24T11:50:04","date_gmt":"2023-02-24T11:50:04","guid":{"rendered":"https:\/\/manuals.seakeeper.com\/seakeeper\/seakeeper-35-30hd-operation-manual-90269-7-copy\/specifications-and-summary\/"},"modified":"2024-01-16T12:34:14","modified_gmt":"2024-01-16T12:34:14","slug":"specifications-and-summary","status":"publish","type":"page","link":"https:\/\/manuals.seakeeper.com\/seakeeper\/seakeeper-40-operation-manual-rev-1\/specifications-and-summary\/","title":{"rendered":"7.0 Specifications and Summary"},"content":{"rendered":"\n
<\/th>Seakeeper<\/span> 40<\/th><\/tr><\/thead>
Rated RPM<\/strong><\/td>5,150 RPM<\/td><\/tr>
Angular Momentum at Rated RPM<\/strong><\/td>40,000 N-m-s<\/td><\/tr>
Anti-Rolling Torque at Rated RPM<\/strong><\/td>104,720 N-m<\/td><\/tr>
Spool-up Time to Rated Speed<\/strong><\/td>70 minutes (5,150 RPM)<\/td><\/tr>
Spool-up Time to Stabilization <\/strong><\/td>49 minutes (4,380 RPM)<\/td><\/tr>
Spool-up Power<\/strong>
AC Motor
DC Control<\/td>
5,000 Watts Max
240 Watts<\/td><\/tr>
Operating Power<\/strong>
AC Motor (Sea state dependent)
DC Control<\/td>		1,900-4,400 Watts
240 Watts<\/td><\/tr>
Voltage<\/strong>
AC Input
DC Input<\/td>
208-230 VAC (\u00b110%), 50\/60 Hz, Single Phase, 30 A
24 VDC @ 15 A (Controls) and 24 VDC @ 20 A (Seawater Pump)<\/td><\/tr>
Seawater Supply to Heat Exchanger<\/strong><\/td>15 GPM (57 LPM) maximum
13 GPM (49 LPM) minimum<\/td><\/tr>
Ambient Air Temperature<\/strong><\/td>32\u02da – 140\u02daF (0 – 60\u02daC)<\/td><\/tr>
Weight<\/strong><\/td>4,074 lbs (1,848 kg)<\/td><\/tr>
Envelope Dimensions<\/strong><\/td>54.3 L X 55.9 W X 40.6 H (inches)
1.38 L x 1.42 W x 1.04 H (meters)<\/td><\/tr>
Noise Output<\/strong><\/td>At full operating RPM, steady state noise measured in the factory at a 1-meter distance measures 72-74 dBC (sound levels may be higher during spool-up).<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n
\n
\"\"<\/figure>\n<\/div>\n\n\n
\n\n\n\n

Arrangement<\/strong>
The Seakeeper<\/span> 40 consists of the Flywheel, Enclosure, Foundation, Electronics, Brake, Cooling, and Cover Subsystems.

Installation Location
<\/strong>The Seakeeper<\/span> is a torque device and does not have to be installed in a specific hull location or on the centerline. However, the Seakeeper<\/span> should not<\/strong> be installed forward of the longitudinal center of gravity in a planing vessel.

Mounting Dimensions
<\/strong>See Drawing No. 90714 \u2013 Seakeeper<\/span> 40 Bolt-In Installation Details.

Loads<\/strong>
The installer is responsible for designing the foundation to which the Seakeeper<\/span> is attached and for ensuring that this foundation can safely transfer the concentrated Seakeeper<\/span> loads from the frame to the adjacent hull structure. Loads that the Seakeeper<\/span> imposes on the hull structure are explained on Drawing No. 90714 \u2013 Seakeeper<\/span> 40 Bolt-In Installation Details; these loads do NOT include vessel motion accelerations, such as vertical slam loads which can be high for higher speed vessels.

Cooling<\/strong>
The Seakeeper<\/span> bearings, Motor Drive Box, and hydraulic manifold are cooled by a closed water \/ glycol mix cooling loop that incorporates a seawater heat exchanger. The installer is responsible for providing 13 \u2013 15 GPM (49 – 57 LPM) raw water at ambient sea temperature and a maximum pressure of 20 psi (1.4 bar) to the heat exchanger.

Electrical<\/strong>
The installer is responsible for supplying 208-230 VAC, 50\/60 Hz, single phase power on a (30 A for Seakeeper<\/span> 40) service to the Motor Drive Box, 24 VDC at 15 A service to the Seakeeper<\/span> Control System, and 24 VDC at 20 A service for the DC Seawater Pump. Separate circuit breakers should be used for each Motor Drive Box in multiple Seakeeper<\/span> installations. Similarly, separate circuit breakers should be used for each Seakeeper<\/span> Control System and DC Seawater Pump in multiple Seakeeper<\/span> installations.

Operator Controls
<\/strong>A ConnectBox user interface or a customer-supplied MFD or optional 5″ display is used to start, operate, monitor, and shutdown the Seakeeper<\/span>.

Performance<\/strong>
Reduction of boat roll is a function of the boat\u2019s displacement, transverse metacentric height (GMT<\/sub>) and hull damping as well as the operating conditions (speed and heading with respect to waves) and sea state. The Seakeeper<\/span> controller regulates the active hydraulic brake to ensure the Seakeeper<\/span>\u2019s anti-roll torque is maximized regardless of hull characteristics or operating conditions.

Alarm and Monitoring<\/strong>
Sensors, alarms and shutdowns are provided to allow unattended operation. Sensors measure Seakeeper<\/span> and drive temperatures, vacuum pressure, gimbal angle, brake pressure, and ship motion. The Seakeeper<\/span> controller sends sensor values and alarm information to the display and also locks the brake and shuts down the motor drive in the event of an alarm condition. Seakeeper<\/span> operating history during faults or alarms is recorded in the controller\u2019s memory for subsequent recall if service is needed. Seakeeper<\/span> may access the Seakeeper<\/span>\u2019s software to gather run hours, bearing loading, and hull slamming information.

Safety<\/strong>
The brake automatically locks the Seakeeper<\/span> so it cannot generate excessive anti-rolling torque loads in the event of a system fault or alarm, loss of electrical power or loss of brake pressure. The brake can be locked from the Display or by shutting off AC and DC power at the supply breakers.<\/p>\n","protected":false},"excerpt":{"rendered":"

Seakeeper 40 Rated RPM 5,150 RPM Angular Momentum at Rated RPM 40,000 N-m-s Anti-Rolling Torque at Rated RPM 104,720 N-m Spool-up Time to Rated Speed 70 minutes (5,150 RPM) Spool-up Time to Stabilization 49 minutes (4,380 RPM) Spool-up PowerAC MotorDC Control 5,000 Watts Max240 Watts Operating PowerAC Motor (Sea state dependent)DC Control 1,900-4,400 Watts240 Watts […]<\/p>\n","protected":false},"author":9,"featured_media":0,"parent":12538,"menu_order":0,"comment_status":"closed","ping_status":"closed","template":"","meta":{"_acf_changed":false,"footnotes":""},"manual":[275],"model":[],"document_type":[],"hidden":[],"class_list":["post-12601","page","type-page","status-publish","hentry","manual-seakeeper-40-operation-manual-rev-1"],"acf":[],"_links":{"self":[{"href":"https:\/\/manuals.seakeeper.com\/seakeeper\/wp-json\/wp\/v2\/pages\/12601","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/manuals.seakeeper.com\/seakeeper\/wp-json\/wp\/v2\/pages"}],"about":[{"href":"https:\/\/manuals.seakeeper.com\/seakeeper\/wp-json\/wp\/v2\/types\/page"}],"author":[{"embeddable":true,"href":"https:\/\/manuals.seakeeper.com\/seakeeper\/wp-json\/wp\/v2\/users\/9"}],"replies":[{"embeddable":true,"href":"https:\/\/manuals.seakeeper.com\/seakeeper\/wp-json\/wp\/v2\/comments?post=12601"}],"version-history":[{"count":6,"href":"https:\/\/manuals.seakeeper.com\/seakeeper\/wp-json\/wp\/v2\/pages\/12601\/revisions"}],"predecessor-version":[{"id":18067,"href":"https:\/\/manuals.seakeeper.com\/seakeeper\/wp-json\/wp\/v2\/pages\/12601\/revisions\/18067"}],"up":[{"embeddable":true,"href":"https:\/\/manuals.seakeeper.com\/seakeeper\/wp-json\/wp\/v2\/pages\/12538"}],"wp:attachment":[{"href":"https:\/\/manuals.seakeeper.com\/seakeeper\/wp-json\/wp\/v2\/media?parent=12601"}],"wp:term":[{"taxonomy":"manual","embeddable":true,"href":"https:\/\/manuals.seakeeper.com\/seakeeper\/wp-json\/wp\/v2\/manual?post=12601"},{"taxonomy":"model","embeddable":true,"href":"https:\/\/manuals.seakeeper.com\/seakeeper\/wp-json\/wp\/v2\/model?post=12601"},{"taxonomy":"document_type","embeddable":true,"href":"https:\/\/manuals.seakeeper.com\/seakeeper\/wp-json\/wp\/v2\/document_type?post=12601"},{"taxonomy":"hidden","embeddable":true,"href":"https:\/\/manuals.seakeeper.com\/seakeeper\/wp-json\/wp\/v2\/hidden?post=12601"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}