{"id":10371,"date":"2022-09-13T15:54:23","date_gmt":"2022-09-13T15:54:23","guid":{"rendered":"https:\/\/manuals.seakeeper.com\/seakeeper\/seakeeper-9-7hd-installation-manual-90222-9-copy\/installation-checklist-and-supplies\/installation-checklist\/"},"modified":"2023-03-07T16:27:15","modified_gmt":"2023-03-07T16:27:15","slug":"installation-checklist","status":"publish","type":"page","link":"https:\/\/manuals.seakeeper.com\/seakeeper\/seakeeper-9-installation-manual-rev10\/installation-checklist-and-supplies\/installation-checklist\/","title":{"rendered":"5.1 Installation Checklist"},"content":{"rendered":"\n

Please Complete Checklist and E-mail to <\/strong>
customerservice@seakeeper.com<\/a> or telefax to +1.410.326.1199<\/strong><\/p>\n\n\n\n

5.1.1 Mechanical Checklist
(Reference Installation Manual Section: Mechanical Installation)<\/h2>\n\n\n\n
\n
\n

_____ Seakeeper<\/span><\/span><\/span> foundation installed in hull<\/p>\n\n\n\n

_____ Foundation bolts torqued to specification<\/p>\n<\/div>\n<\/div>\n\n\n\n\n\n

5.1.2 Electrical Checklist
(Reference Seakeeper<\/span> Drawing No. 90257 \u2013 Seakeeper<\/span> 9 Cable Block Diagram & Installation Manual Section: Electrical Installation)<\/h2>\n\n\n\n

Mount Components<\/strong><\/p>\n\n\n\n

_____ Display (near helm)<\/p>\n\n\n\n

<\/div>\n\n\n\n

Connect Customer Supplied Cables<\/strong><\/p>\n\n\n\n

Cable 6 (Customer supplied)<\/strong><\/p>\n\n\n\n

_____ Install lugs on both ends of customer-supplied 10 AWG ground cable<\/p>\n\n\n\n

_____ Connect one end of Cable 6 to nearest vessel ground and other end to Seakeeper<\/span> 9 rear brace<\/p>\n\n\n\n

<\/div>\n\n\n\n

Connect Seakeeper<\/span> Supplied Cables<\/strong><\/p>\n\n\n\n

Cable 1<\/strong><\/p>\n\n\n\n

_____ Connect Cable 1 from Seakeeper<\/span> to 24 VDC power at customer-supplied connection box or directly
to circuit breaker<\/p>\n\n\n\n

_____ Plug connector of Cable 1 into mating connector on Seakeeper<\/span> wire harness<\/p>\n\n\n\n

Cable 2<\/strong><\/p>\n\n\n\n

_____ Connect Cable 2 from Drive Box to 230 VAC single phase at customer-supplied connection box
or directly to circuit breaker<\/p>\n\n\n\n

Cable 8<\/strong><\/p>\n\n\n\n

_____ Connect Cable 8 from Seakeeper<\/span> to 24 VDC \/10 A power at customer-supplied connection box
or directly to circuit breaker<\/p>\n\n\n\n

_____ Plug connector of Cable 8 into mating connector on Seakeeper<\/span> wire harness at DC SW Pump In<\/em><\/p>\n\n\n\n

Cable 5<\/strong><\/p>\n\n\n\n

_____ Connect Cable 5 from DC SW Pump Out<\/em> to 24 VDC seawater pump<\/p>\n\n\n\n

Cable 3<\/strong><\/p>\n\n\n\n

_____ Connect female end of CAN communications Cable 3 to mating connector on Seakeeper<\/span> wire
harness<\/p>\n\n\n\n

_____ Route CAN communications Cable 3 from Seakeeper<\/span> to helm (male end goes to helm)<\/p>\n\n\n\n

_____ Connect male end of CAN communications Cable 3 at helm to CAN Tee Adapter<\/p>\n\n\n\n

_____ Connect Display and Seakeeper<\/span>-supplied Cable 4 to CAN Tee Adapter with CAN Terminator<\/p>\n\n\n\n\n\n

5.1.3 Cooling Checklist
(Reference Installation Manual Section: Cooling Installation)<\/h2>\n\n\n\n

_____ Verify coolant level in heat exchanger coolant reservoir (2\/3 maximum)<\/p>\n\n\n\n

_____ Connect seawater hoses \/ open sea cocks to heat exchanger and test seawater pump<\/p>\n\n\n\n

_____ Verify 4 GPM (15 LPM) minimum and 8 GPM (30 LPM) maximum seawater flow through heat
heat exchanger under all operating conditions of the boat<\/p>\n\n\n\n\n\n

5.1.4 Start Up Checklist
(Reference Installation Manual Section: Start Up & Operation Manual Section: System Operation)<\/h2>\n\n\n\n

_____ Remove lifting eyebolts and install cover panels<\/p>\n\n\n\n

_____ Turn on 24 VDC circuit breakers<\/p>\n\n\n\n

_____ Turn on 230 VAC circuit breaker<\/p>\n\n\n\n

_____ Verify display works and no ALARMS are present<\/p>\n\n\n\n

_____ If display does not work, turn off both circuit breakers immediately<\/p>\n\n\n\n

_____ Check polarity of 24 VDC power per Section 2.2.5<\/p>\n\n\n\n

_____ Follow instructions in Installation Manual Section: Start Up Instructions to turn on the Seakeeper<\/span><\/p>\n\n\n\n

_____ Verify seawater pump turns on while the Seakeeper<\/span> is turned ON<\/p>\n\n\n\n

_____ Verify no ALARMS are present<\/p>\n\n\n\n

_____ Follow instructions in Installation Manual Section: Startup Instructions to turn off the Seakeeper<\/span><\/p>\n\n\n\n

_____ AC & DC power and seawater pump may be turned off after the Seakeeper<\/span> is turned off by placing the
Seakeeper<\/span> in LOCK mode and turning the Seakeeper<\/span> off<\/p>\n\n\n\n

_____ Seakeeper<\/span> 9 takes 4+ hours to coast down to 0 RPM from full speed<\/p>\n","protected":false},"excerpt":{"rendered":"

Please Complete Checklist and E-mail to customerservice@seakeeper.com or telefax to +1.410.326.1199 5.1.1 Mechanical Checklist(Reference Installation Manual Section: Mechanical Installation) _____ Seakeeper foundation installed in hull _____ Foundation bolts torqued to specification 5.1.2 Electrical Checklist(Reference Seakeeper Drawing No. 90257 \u2013 Seakeeper 9 Cable Block Diagram & Installation Manual Section: Electrical Installation) Mount Components _____ Display (near […]<\/p>\n","protected":false},"author":9,"featured_media":0,"parent":10369,"menu_order":0,"comment_status":"closed","ping_status":"closed","template":"","meta":{"_acf_changed":false,"footnotes":""},"manual":[261],"model":[],"document_type":[],"hidden":[],"class_list":["post-10371","page","type-page","status-publish","hentry","manual-seakeeper-9-installation-manual-rev10"],"acf":[],"_links":{"self":[{"href":"https:\/\/manuals.seakeeper.com\/seakeeper\/wp-json\/wp\/v2\/pages\/10371","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/manuals.seakeeper.com\/seakeeper\/wp-json\/wp\/v2\/pages"}],"about":[{"href":"https:\/\/manuals.seakeeper.com\/seakeeper\/wp-json\/wp\/v2\/types\/page"}],"author":[{"embeddable":true,"href":"https:\/\/manuals.seakeeper.com\/seakeeper\/wp-json\/wp\/v2\/users\/9"}],"replies":[{"embeddable":true,"href":"https:\/\/manuals.seakeeper.com\/seakeeper\/wp-json\/wp\/v2\/comments?post=10371"}],"version-history":[{"count":4,"href":"https:\/\/manuals.seakeeper.com\/seakeeper\/wp-json\/wp\/v2\/pages\/10371\/revisions"}],"predecessor-version":[{"id":13390,"href":"https:\/\/manuals.seakeeper.com\/seakeeper\/wp-json\/wp\/v2\/pages\/10371\/revisions\/13390"}],"up":[{"embeddable":true,"href":"https:\/\/manuals.seakeeper.com\/seakeeper\/wp-json\/wp\/v2\/pages\/10369"}],"wp:attachment":[{"href":"https:\/\/manuals.seakeeper.com\/seakeeper\/wp-json\/wp\/v2\/media?parent=10371"}],"wp:term":[{"taxonomy":"manual","embeddable":true,"href":"https:\/\/manuals.seakeeper.com\/seakeeper\/wp-json\/wp\/v2\/manual?post=10371"},{"taxonomy":"model","embeddable":true,"href":"https:\/\/manuals.seakeeper.com\/seakeeper\/wp-json\/wp\/v2\/model?post=10371"},{"taxonomy":"document_type","embeddable":true,"href":"https:\/\/manuals.seakeeper.com\/seakeeper\/wp-json\/wp\/v2\/document_type?post=10371"},{"taxonomy":"hidden","embeddable":true,"href":"https:\/\/manuals.seakeeper.com\/seakeeper\/wp-json\/wp\/v2\/hidden?post=10371"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}