{"id":17019,"date":"2026-03-30T17:55:57","date_gmt":"2026-03-30T17:55:57","guid":{"rendered":"https:\/\/manuals.seakeeper.com\/ride\/mechanical-installation-manual-750-1500-copy\/12-actuator-and-blade-installation\/12-2-exposed-cable-entry\/"},"modified":"2026-04-01T16:35:33","modified_gmt":"2026-04-01T16:35:33","slug":"12-2-exposed-cable-entry","status":"publish","type":"page","link":"https:\/\/manuals.seakeeper.com\/ride\/mechanical-installation-manual-750-1500-375a-and-525a\/12-actuator-and-blade-installation\/12-2-exposed-cable-entry\/","title":{"rendered":"12.2 Exposed Cable Entry"},"content":{"rendered":"\n<ol class=\"wp-block-list\">\n<li>Install the Cable Guide Support in the groove in the Seal Plate.<\/li>\n<\/ol>\n\n\n<div class=\"wp-block-image\">\n<figure class=\"aligncenter size-full is-resized\"><img loading=\"lazy\" decoding=\"async\" width=\"717\" height=\"492\" src=\"https:\/\/manuals.seakeeper.com\/ride\/wp-content\/uploads\/Cable-Guide-Support-in-Groove.png\" alt=\"\" class=\"wp-image-14662\" style=\"width:578px;height:auto\"\/><figcaption class=\"wp-element-caption\">Figure 81 \u2013 Cable Guide Support in Groove<\/figcaption><\/figure>\n<\/div>\n\n\n<ol start=\"2\" class=\"wp-block-list\">\n<li>Place the Actuator into the Actuator Plate. The Actuator can be mounted with cable exiting to port or starboard side, so select the correct side to align with the Cable Guide. The arms should be pointed out toward the installer. One arm is stiffer than the other.<\/li>\n\n\n\n<li>Position the Seal Plate over the arms and Actuator and align the countersunk holes on the bottom surface. \n<ul class=\"wp-block-list\">\n<li>On 750 Controller systems the two (2) supplied plastic debris caps will need to be inserted between the Seal Plate and Actuator Plate at this stage. See Figure 72.<\/li>\n<\/ul>\n<\/li>\n\n\n\n<li>Route the Actuator Cable through the Cable Guide Support.<\/li>\n\n\n\n<li>Thread locker and thread in the top four (4) M6-1.0 x 30 mm Hex Head Bolts with M6 Washers to align the Seal Plate with the Wedge Pack Assembly, but&nbsp;<strong><u>do not tighten<\/u><\/strong>. There should be a small gap (about 2 mm) between the top of the Seal Plate and the Actuator Plate. (Quantity four [4] bolts for 525 Controllers and six [6] for 750 mm Controllers) See&nbsp;<a href=\"https:\/\/manuals.seakeeper.com\/ride\/mechanical-installation-manual-750-1500-375a-and-525a\/12-actuator-and-blade-installation\/12-1-concealed-cable-entry\/#TopA\" target=\"_blank\" rel=\"noreferrer noopener\">Figure 71 \u2013 Seal Plate Top Screw Installation<\/a>.<\/li>\n\n\n\n<li>Visually center the Actuator to the Seal Plate by comparing small length of protruding Actuator housing on each end.<\/li>\n\n\n\n<li>Apply thread locker and insert the bottom six (6) M6-1.0 x 16 mm Torx Flathead Screws. Torque to 80 in-lbs (9 N-m) in an alternating pattern. Repeat the top torquing sequence two (2) times or until the bolts do not rotate when achieving the torque (Quantity nine [9] bolts for 525 Controllers and ten [10] for 750 mm Controllers) See&nbsp;<a href=\"https:\/\/manuals.seakeeper.com\/ride\/mechanical-installation-manual-750-1500-375a-and-525a\/12-actuator-and-blade-installation\/12-1-concealed-cable-entry\/#BottomA\" data-type=\"link\" data-id=\"https:\/\/manuals.seakeeper.com\/ride\/seakeeper-ride-ride-750-series-controllers-mechanical-installation-manual\/12-actuator-and-blade-installation\/12-1-concealed-cable-entry\/\" target=\"_blank\" rel=\"noreferrer noopener\">Figure 74 \u2013 Bottom Bolts Installation<\/a>.<\/li>\n\n\n\n<li>Torque the top four (4) M6-1.0 x 30 mm Hex Head Bolts to 50 in-lbs (5.7 N-m) in an alternating pattern. Repeat the top torquing sequence two (2) times or until the bolts do not rotate when achieving the torque. This ensures an even clamping force is applied across the Actuator. (Quantity four [4] bolts for 525 Controllers and six [6] for 750 mm Controllers).<\/li>\n<\/ol>\n\n\n\n<h2 class=\"wp-block-heading\">Verify Seal Plate Angle<\/h2>\n\n\n\n<p>At this point the Seal Plate angle can be verified with a straight edge to ensure the wedge pack selection was correct. Following the procedure from <a href=\"https:\/\/manuals.seakeeper.com\/ride\/mechanical-installation-manual-750-1500-375a-and-525a\/6-measure-transom-angle\/6-2-hulls-with-unique-stern-features\/\" data-type=\"page\" data-id=\"14727\" target=\"_blank\" rel=\"noreferrer noopener\">Section 6.2<\/a> to check the angle of the Seal Plate. If adjustments are desired, remove Seal Plate and rebuild the Wedge Pack following <a href=\"https:\/\/manuals.seakeeper.com\/ride\/mechanical-installation-manual-750-1500-375a-and-525a\/6-measure-transom-angle\/6-3-wedge-pack-angle-adjustment\/\" data-type=\"link\" data-id=\"https:\/\/manuals.seakeeper.com\/ride\/seakeeper-ride-ride-750-series-controllers-mechanical-installation-manual\/7-assemble-wedge-pack\/assemble-wedge-pack-introduction\/\" target=\"_blank\" rel=\"noreferrer noopener\">Section 6.3<\/a> in place until desired Seal Plate angle is achieved.<\/p>\n\n\n<div class=\"wp-block-image\">\n<figure class=\"aligncenter size-full\"><img loading=\"lazy\" decoding=\"async\" width=\"640\" height=\"351\" src=\"https:\/\/manuals.seakeeper.com\/ride\/wp-content\/uploads\/Cable-Guide-Pilot-Holes-Cropped.jpg\" alt=\"\" class=\"wp-image-14664\"\/><figcaption class=\"wp-element-caption\">Figure 82 \u2013 Cable Guide Pilot Holes<\/figcaption><\/figure>\n<\/div>\n\n\n<ol start=\"9\" class=\"wp-block-list\">\n<li>Mount the Cable Guide Support in line with the natural path of the Actuator Cable to the transom. Pre-drill two (2) mounting screw pilot holes using a 3\/32 in. (2.4 mm) bit. Inject sealant into the holes. Insert two (2) No. 8 x 0.75 in. screws and tighten with a Phillips head screwdriver.<\/li>\n\n\n\n<li>Route the Actuator cable over the Inner Cable Guide. Feed as much cable as possible through the Cable Gland Tube.<\/li>\n\n\n\n<li>Tighten the Cable Gland around the Actuator Cable on the inboard side of the transom (See&nbsp;<a href=\"https:\/\/manuals.seakeeper.com\/ride\/mechanical-installation-manual-750-1500-375a-and-525a\/12-actuator-and-blade-installation\/12-1-concealed-cable-entry\/#Gland2A\" data-type=\"link\" data-id=\"https:\/\/manuals.seakeeper.com\/ride\/seakeeper-ride-ride-750-series-controllers-mechanical-installation-manual\/12-actuator-and-blade-installation\/12-1-concealed-cable-entry\/\" target=\"_blank\" rel=\"noreferrer noopener\">Figure 75 \u2013 Cable Gland Installation Inboard of Transom<\/a>). The Cable Gland should be snug to prevent leaking, but do not overtighten. If the Cable Gland was not selected, apply marine adhesive sealant to the cable sheath and cable hole to seal the penetration from outside the hull. <strong>Note:<\/strong>&nbsp;The Cable Gland must have the rubber grommet in place to properly seal. The outside of the cable must be clean of debris, dust, adhesives, etc. to properly seal. Do not allow acetone to come in contact with the Controller Cable Gland Sealing Nut.<\/li>\n\n\n\n<li>Place the Outer Cable Guide over the Inner Cable Guide. Mark the location of the six (6) mounting screw holes. Drill 3\/32 (2.4 mm) pilot holes in these six (6) locations.<\/li>\n\n\n\n<li>Inject sealant into the pilot holes for the mounting screws for the Outer Cable Guide. Using a Phillips head screwdriver, install the six (6) mounting screws into the hull and hand-tighten.<\/li>\n<\/ol>\n\n\n<div class=\"wp-block-image\">\n<figure class=\"aligncenter size-full is-resized\"><img loading=\"lazy\" decoding=\"async\" width=\"662\" height=\"648\" src=\"https:\/\/manuals.seakeeper.com\/ride\/wp-content\/uploads\/Outer-Cable-Guide-Installation-1.png\" alt=\"\" class=\"wp-image-14666\" style=\"width:450px\"\/><figcaption class=\"wp-element-caption\">Figure 83 \u2013 Mounting Outer Cable Guide<\/figcaption><\/figure>\n<\/div>\n\n\n<ol start=\"14\" class=\"wp-block-list\">\n<li>Attach the bonding wires and Actuator Plate Anodes.\n<ul class=\"wp-block-list\">\n<li>Attach one terminal end of one bonding wire to the upper right corner of the Transom Plate using one (1) M2-0.7 x 6 mm Phillips Head Screw.<\/li>\n\n\n\n<li>Attach one terminal end of another bonding wire the front right-hand side of the Seal Plate using one (1) M2-0.7 x 6 mm Phillips Head Screw.<\/li>\n\n\n\n<li>Install the two (2) Actuator Plate Anodes using two M5-0.8 x 20 mm Button Head Screws. Slide the two free terminal ends of the bonding wires over the right-hand anode screw while inserting creating a continuous connection between the Transom Plate, Actuator Plate, and Seal Plate.\n<ul class=\"wp-block-list\">\n<li>Note: Install the wire to the starboard side arm before mounting the Blade.<\/li>\n<\/ul>\n<\/li>\n<\/ul>\n<\/li>\n\n\n\n<li>Install the Blade to the Actuator Arms using the four (4) M8-1.25\u00d720 mm screws and their washers. Before torquing the bolts, push the Actuator Arms firmly down against the Blade supporting edge. Torque these four (4) bolts to 80 in-lbs (9.0 N-m) in an \u2018X\u2019 pattern (<a href=\"https:\/\/manuals.seakeeper.com\/ride\/mechanical-installation-manual-750-1500-375a-and-525a\/12-actuator-and-blade-installation\/12-1-concealed-cable-entry\/#BladeA\" data-type=\"link\" data-id=\"https:\/\/manuals.seakeeper.com\/ride\/seakeeper-ride-ride-750-series-controllers-mechanical-installation-manual\/12-actuator-and-blade-installation\/12-1-concealed-cable-entry\/\" target=\"_blank\" rel=\"noreferrer noopener\">Figure 77 \u2013 Blade Installation<\/a>).<\/li>\n\n\n\n<li>Once installed, push the Blade all the way down and verify that the Blade is not contacting the Seal Plate. There should be a small, even gap between the Blade and the Seal Plate. Contact&nbsp;<span translate=\"no\"><span translate=\"no\">Seakeeper<\/span><\/span>&nbsp;if the Blade does not meet this requirement.\n<ul class=\"wp-block-list\">\n<li>Before torquing, the Blade can be slid up and down slightly to bring it closer and farther away from the Seal Plate, respectively. If the Blade is rubbing and creating friction against the Seal Plate, or if the gap appears too large, adjust the Blade accordingly. Contact <span translate=\"no\"><span translate=\"no\"><span translate=\"no\"><span translate=\"no\">Seakeeper<\/span><\/span><\/span><\/span> if there are still concerns with Blade gap tolerance after following these instructions. (<a href=\"https:\/\/manuals.seakeeper.com\/ride\/mechanical-installation-manual-750-1500-375a-and-525a\/12-actuator-and-blade-installation\/12-1-concealed-cable-entry\/#GapAdjustA\">Figure 78 &#8211; Blade Gap Adjustment<\/a>)<\/li>\n<\/ul>\n<\/li>\n<\/ol>\n\n\n\n<p><strong>Note:&nbsp;<\/strong>Maintaining this gap between the Blade and Seal Plate is critical to maintaining factory tested failure mode performance. If the gap between the Blade and Seal Plate is too large, system performance will fall off. If the Blade contacts the Seal Plate, the friction will slow down the system\u2019s response time, also reducing performance.<\/p>\n\n\n\n<p>To maintain the factory fitment:<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li>Do not apply anti-fouling coating to the surfaces between the Blade and Seal Plate in order to avoid changing the fit of those parts.<\/li>\n\n\n\n<li>Always keep the surfaces between the Blade and Seal Plate clean and free from debris, including naturally occurring debris (such as marine debris) and other debris (such as paint or coating.<\/li>\n\n\n\n<li>When repairing or replacing any components on the Controller, confirm that the Blade rotates by hand. Resistance will be felt from the Actuator, but there must be no additional grinding or friction inhibiting movement.<\/li>\n<\/ul>\n\n\n\n<ol start=\"17\" class=\"wp-block-list\">\n<li>Install the Blade Anode using two M5-0.8 x 20 mm Button Head Screws. Slide the other terminal end of the bonding wire over the right-hand side screw while inserting. (<a href=\"https:\/\/manuals.seakeeper.com\/ride\/mechanical-installation-manual-750-1500-375a-and-525a\/12-actuator-and-blade-installation\/12-1-concealed-cable-entry\/#BladeAnodeA\">Figure 79 &#8211; Blade Anode Installation<\/a>)<\/li>\n<\/ol>\n\n\n\n<p>See <a href=\"https:\/\/manuals.seakeeper.com\/ride\/mechanical-installation-manual-750-1500-375a-and-525a\/12-actuator-and-blade-installation\/12-1-concealed-cable-entry\/#BondingA\">Figure 80<\/a> for Anode and Bonding Wire overview.<\/p>\n","protected":false},"excerpt":{"rendered":"<p>Verify Seal Plate Angle At this point the Seal Plate angle can be verified with a straight edge to ensure the wedge pack selection was correct. Following the procedure from Section 6.2 to check the angle of the Seal Plate. If adjustments are desired, remove Seal Plate and rebuild the Wedge Pack following Section 6.3 [&hellip;]<\/p>\n","protected":false},"author":17,"featured_media":0,"parent":17013,"menu_order":0,"comment_status":"closed","ping_status":"closed","template":"","meta":{"_acf_changed":false,"footnotes":""},"manual":[375],"model":[],"document_type":[],"hidden":[],"class_list":["post-17019","page","type-page","status-publish","hentry","manual-mechanical-installation-manual-750-1500-375a-and-525a"],"acf":[],"_links":{"self":[{"href":"https:\/\/manuals.seakeeper.com\/ride\/wp-json\/wp\/v2\/pages\/17019","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/manuals.seakeeper.com\/ride\/wp-json\/wp\/v2\/pages"}],"about":[{"href":"https:\/\/manuals.seakeeper.com\/ride\/wp-json\/wp\/v2\/types\/page"}],"author":[{"embeddable":true,"href":"https:\/\/manuals.seakeeper.com\/ride\/wp-json\/wp\/v2\/users\/17"}],"replies":[{"embeddable":true,"href":"https:\/\/manuals.seakeeper.com\/ride\/wp-json\/wp\/v2\/comments?post=17019"}],"version-history":[{"count":4,"href":"https:\/\/manuals.seakeeper.com\/ride\/wp-json\/wp\/v2\/pages\/17019\/revisions"}],"predecessor-version":[{"id":17153,"href":"https:\/\/manuals.seakeeper.com\/ride\/wp-json\/wp\/v2\/pages\/17019\/revisions\/17153"}],"up":[{"embeddable":true,"href":"https:\/\/manuals.seakeeper.com\/ride\/wp-json\/wp\/v2\/pages\/17013"}],"wp:attachment":[{"href":"https:\/\/manuals.seakeeper.com\/ride\/wp-json\/wp\/v2\/media?parent=17019"}],"wp:term":[{"taxonomy":"manual","embeddable":true,"href":"https:\/\/manuals.seakeeper.com\/ride\/wp-json\/wp\/v2\/manual?post=17019"},{"taxonomy":"model","embeddable":true,"href":"https:\/\/manuals.seakeeper.com\/ride\/wp-json\/wp\/v2\/model?post=17019"},{"taxonomy":"document_type","embeddable":true,"href":"https:\/\/manuals.seakeeper.com\/ride\/wp-json\/wp\/v2\/document_type?post=17019"},{"taxonomy":"hidden","embeddable":true,"href":"https:\/\/manuals.seakeeper.com\/ride\/wp-json\/wp\/v2\/hidden?post=17019"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}