{"id":16927,"date":"2026-03-30T17:55:55","date_gmt":"2026-03-30T17:55:55","guid":{"rendered":"https:\/\/manuals.seakeeper.com\/ride\/mechanical-installation-manual-750-1500-copy\/inventory-parts\/"},"modified":"2026-04-01T14:40:49","modified_gmt":"2026-04-01T14:40:49","slug":"inventory-parts","status":"publish","type":"page","link":"https:\/\/manuals.seakeeper.com\/ride\/mechanical-installation-manual-750-1500-375a-and-525a\/inventory-parts\/","title":{"rendered":"4. Inventory Parts"},"content":{"rendered":"\n

Please review all parts included before proceeding. The following figure and table describe all parts included in the assembly. Review parts and ensure all parts are present before starting the installation procedure.<\/p>\n\n\n\n

Components shown are per Controller. Dual Actuator systems will have two (2) times the components listed, and Quad Actuator systems will have four (4) times the components listed.<\/p>\n\n\n\n

\"\"<\/figure>
\n
    \n
  1. Blade<\/li>\n\n\n\n
  2. Seal Plate<\/li>\n\n\n\n
  3. Actuator<\/li>\n\n\n\n
  4. Actuator Plate<\/li>\n\n\n\n
  5. 3 Degree Wedge Plate<\/li>\n\n\n\n
  6. 4 Degree Wedge Plate<\/li>\n\n\n\n
  7. 5 Degree Wedge Plate<\/li>\n\n\n\n
  8. Transom Plate<\/li>\n<\/ol>\n<\/div><\/div>\n\n\n\n
    \"\"<\/figure>
    \n
      \n
    1. Cable Gland Tube <\/li>\n<\/ol>\n\n\n\n
        \n
      1. Cable Gland Nut <\/li>\n<\/ol>\n\n\n\n
          \n
        1. Outer Cable Guide <\/li>\n<\/ol>\n\n\n\n
            \n
          1. Inner Cable Guide <\/li>\n<\/ol>\n\n\n\n
              \n
            1. Cable Support Guide <\/li>\n<\/ol>\n\n\n\n
                \n
              1. Drill Guide Tube <\/li>\n<\/ol>\n\n\n\n
                  \n
                1. Drill Guide Follower <\/li>\n<\/ol>\n<\/div><\/div>\n\n\n\n
                  \"\"<\/figure>
                  \n

                  ATTENTION: <\/strong>DO NOT pickup the Actuator by the cable or allow it to hang by the cable. Doing so could compromise to the watertight seal of the Actuator and cause system malfunction.<\/p>\n\n\n\n

                  <\/p>\n<\/div><\/div>\n\n\n

                  \n
                  \"\"<\/figure>\n<\/div>\n\n\n
                  \n\n\n\n

                  Hardware counts below are given in the format: x[375 CONTROLLER] | [525 CONTROLLER] | [750 CONTROLLER]<\/strong> <\/p>\n\n\n\n

                  Wedge Pack Hardware<\/strong><\/td><\/td><\/td><\/td>Positioning Screws<\/strong><\/td><\/tr>
                  \"\"
                  x3 | 4 | 5<\/strong><\/strong>

                  M8-1.25 X 35 mm Hex Head Bolt <\/td>                  		\"\"
                  x3 | 4 | 5<\/strong><\/strong>

                  M8-1.25 X 40 mm Hex Head Bolt <\/td>                  		\"\" <\/strong>
                  x2 | 2 | 4<\/strong><\/strong>

                  M8-1.25 X 55 mm Hex Head Bolt <\/td>
                  \"\"
                  x2 | 2 | 4<\/strong> <\/strong>

                  M8-1.25 X 75 mm Hex Head Bolt <\/td>

                  \"\"
                  x3<\/strong>

                  Phillips No. 10 x 1.5 in. Screw <\/td><\/tr>
                  \"\"
                  x5 | 6 | 9<\/strong><\/strong>

                  M8 Cylindrical Washer for Hex Head <\/td>                  		\"\"
                  x5 | 6 | 9<\/strong><\/strong>

                  Transom Plate Bolt Cover <\/td>                  		\"\"
                  x5 | 6 | 9<\/strong><\/strong>

                  M8 Cylindrical Washer <\/td>                  		\"\"
                  x5 | 6 | 9<\/strong><\/strong>

                  M8 Wedge lock Washer <\/td>                  		\"\"
                  x5 | 6 | 9<\/strong><\/strong>

                  M8-1.25 Hex Nut 

                  <\/td><\/tr>
                  Seal Plate Hardware<\/strong><\/td><\/td><\/td>Blade Hardware<\/strong><\/td><\/td><\/tr>
                  \"\"
                  x4 | 4 | 6<\/strong><\/strong>

                  M6-1.0 x 30 mm Hex Head Bolt <\/td>                  		\"\"
                  x4 | 4 | <\/strong>6<\/strong>
                  M6 Washer<\/td>                  		\"\"
                  x6 | 9 | 10<\/strong><\/strong>

                  M6-1.0 x 16 mm Flathead Screw <\/td>                  		\"\"
                  x4
                  <\/strong>
                  M8-1.25 X 30 mm Hex Head Bolt <\/td>                  		\"\"
                  x4<\/strong>

                  M8 Washer<\/td><\/tr>
                  Cable Routing Hardware<\/strong><\/td><\/td><\/td>Endcaps<\/strong><\/td><\/td><\/tr>
                  \"\"
                  x2<\/strong>

                  Phillips No. 8 x 0.75 in. Screw<\/td>                  		\"\"
                  x2<\/strong>

                  Phillips No. 8 x 1.5 in. Screw<\/td>                  		\"\"
                  x2<\/strong>

                  Phillips No. 10 x 1.0 in. Screw <\/td>                  		\"\"
                  x0 | 0 | 2<\/strong><\/strong>

                  Endcaps (Only included with 750 Controller systems)
                  <\/td>                  		<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n

                  <\/p>\n","protected":false},"excerpt":{"rendered":"

                  Please review all parts included before proceeding. The following figure and table describe all parts included in the assembly. Review parts and ensure all parts are present before starting the installation procedure. Components shown are per Controller. Dual Actuator systems will have two (2) times the components listed, and Quad Actuator systems will have four […]<\/p>\n","protected":false},"author":17,"featured_media":0,"parent":16912,"menu_order":0,"comment_status":"closed","ping_status":"closed","template":"","meta":{"_acf_changed":false,"footnotes":""},"manual":[375],"model":[],"document_type":[],"hidden":[],"class_list":["post-16927","page","type-page","status-publish","hentry","manual-mechanical-installation-manual-750-1500-375a-and-525a"],"acf":[],"_links":{"self":[{"href":"https:\/\/manuals.seakeeper.com\/ride\/wp-json\/wp\/v2\/pages\/16927","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/manuals.seakeeper.com\/ride\/wp-json\/wp\/v2\/pages"}],"about":[{"href":"https:\/\/manuals.seakeeper.com\/ride\/wp-json\/wp\/v2\/types\/page"}],"author":[{"embeddable":true,"href":"https:\/\/manuals.seakeeper.com\/ride\/wp-json\/wp\/v2\/users\/17"}],"replies":[{"embeddable":true,"href":"https:\/\/manuals.seakeeper.com\/ride\/wp-json\/wp\/v2\/comments?post=16927"}],"version-history":[{"count":1,"href":"https:\/\/manuals.seakeeper.com\/ride\/wp-json\/wp\/v2\/pages\/16927\/revisions"}],"predecessor-version":[{"id":17116,"href":"https:\/\/manuals.seakeeper.com\/ride\/wp-json\/wp\/v2\/pages\/16927\/revisions\/17116"}],"up":[{"embeddable":true,"href":"https:\/\/manuals.seakeeper.com\/ride\/wp-json\/wp\/v2\/pages\/16912"}],"wp:attachment":[{"href":"https:\/\/manuals.seakeeper.com\/ride\/wp-json\/wp\/v2\/media?parent=16927"}],"wp:term":[{"taxonomy":"manual","embeddable":true,"href":"https:\/\/manuals.seakeeper.com\/ride\/wp-json\/wp\/v2\/manual?post=16927"},{"taxonomy":"model","embeddable":true,"href":"https:\/\/manuals.seakeeper.com\/ride\/wp-json\/wp\/v2\/model?post=16927"},{"taxonomy":"document_type","embeddable":true,"href":"https:\/\/manuals.seakeeper.com\/ride\/wp-json\/wp\/v2\/document_type?post=16927"},{"taxonomy":"hidden","embeddable":true,"href":"https:\/\/manuals.seakeeper.com\/ride\/wp-json\/wp\/v2\/hidden?post=16927"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}