Updated 05\/21\/2025<\/p>\n\n\n\n
When installing or reinstalling any component of Seakeeper<\/span> Ride, make sure to apply thread locker to bolts. Use a torque wrench to tighten bolts to the correct specification shown below. Be sure to verify torque is achieved with 2 rounds of torque per fastener. Bolts or screws not listed below do not have a torque specification and should be tightened snug to prevent movement but not overtightened. Do not tighten bolts in a straight or circular path, one right after another. Instead, tighten in an alternating or \u2018X\u2019 pattern.<\/p>\n\n\n\n Updated 05\/21\/2025 When installing or reinstalling any component of Seakeeper Ride, make sure to apply thread locker to bolts. Use a torque wrench to tighten bolts to the correct specification shown below. Be sure to verify torque is achieved with 2 rounds of torque per fastener. Bolts or screws not listed below do not have a torque […]<\/p>\n","protected":false},"author":15,"featured_media":0,"parent":15015,"menu_order":0,"comment_status":"closed","ping_status":"closed","template":"","meta":{"_acf_changed":false,"footnotes":""},"manual":[],"model":[],"document_type":[],"hidden":[],"class_list":["post-15016","page","type-page","status-publish","hentry"],"acf":[],"_links":{"self":[{"href":"https:\/\/manuals.seakeeper.com\/ride\/wp-json\/wp\/v2\/pages\/15016","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/manuals.seakeeper.com\/ride\/wp-json\/wp\/v2\/pages"}],"about":[{"href":"https:\/\/manuals.seakeeper.com\/ride\/wp-json\/wp\/v2\/types\/page"}],"author":[{"embeddable":true,"href":"https:\/\/manuals.seakeeper.com\/ride\/wp-json\/wp\/v2\/users\/15"}],"replies":[{"embeddable":true,"href":"https:\/\/manuals.seakeeper.com\/ride\/wp-json\/wp\/v2\/comments?post=15016"}],"version-history":[{"count":4,"href":"https:\/\/manuals.seakeeper.com\/ride\/wp-json\/wp\/v2\/pages\/15016\/revisions"}],"predecessor-version":[{"id":16315,"href":"https:\/\/manuals.seakeeper.com\/ride\/wp-json\/wp\/v2\/pages\/15016\/revisions\/16315"}],"up":[{"embeddable":true,"href":"https:\/\/manuals.seakeeper.com\/ride\/wp-json\/wp\/v2\/pages\/15015"}],"wp:attachment":[{"href":"https:\/\/manuals.seakeeper.com\/ride\/wp-json\/wp\/v2\/media?parent=15016"}],"wp:term":[{"taxonomy":"manual","embeddable":true,"href":"https:\/\/manuals.seakeeper.com\/ride\/wp-json\/wp\/v2\/manual?post=15016"},{"taxonomy":"model","embeddable":true,"href":"https:\/\/manuals.seakeeper.com\/ride\/wp-json\/wp\/v2\/model?post=15016"},{"taxonomy":"document_type","embeddable":true,"href":"https:\/\/manuals.seakeeper.com\/ride\/wp-json\/wp\/v2\/document_type?post=15016"},{"taxonomy":"hidden","embeddable":true,"href":"https:\/\/manuals.seakeeper.com\/ride\/wp-json\/wp\/v2\/hidden?post=15016"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}Location<\/strong><\/td> Hardware Used<\/strong><\/td> Torque (in-lbs)<\/strong><\/td> Torque (N-M)<\/strong><\/td><\/tr> Positioning Screws<\/strong><\/td> Screw<\/td> 20<\/td> 2.3<\/td><\/tr> Wedge Pack Assembly<\/strong><\/td> M8<\/td> 130<\/td> 14.7<\/td><\/tr> Seal Plate to Actuator Plate<\/strong> (Bottom, Torx Drive)<\/td> M6 Flat Head<\/td> 80<\/td> 9.0<\/td><\/tr> Seal Plate to Actuator Plate<\/strong> (Top, Hex Head)<\/td> M6 Hex Head<\/td> 50<\/td> 5.6<\/td><\/tr> Arms to Actuator<\/strong><\/td> M10<\/td> 300 (25 ft-lbs)<\/td> 33.9<\/td><\/tr> Anodes <\/strong>*No thread locker<\/td> M5<\/td> 25<\/td> 2.8<\/td><\/tr> Blades to Arms<\/strong><\/td> M8<\/td> 130<\/td> 14.7<\/td><\/tr><\/tbody><\/table><\/figure>\n","protected":false},"excerpt":{"rendered":"